Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Highlights:

   - Gustavo A. R. Silva keeps working on the implicit switch fallthru
     changes.

   - Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
     Luca Coelho.

   - Re-enable ASPM in r8169, from Kai-Heng Feng.

   - Add virtual XFRM interfaces, which avoids all of the limitations of
     existing IPSEC tunnels. From Steffen Klassert.

   - Convert GRO over to use a hash table, so that when we have many
     flows active we don't traverse a long list during accumluation.

   - Many new self tests for routing, TC, tunnels, etc. Too many
     contributors to mention them all, but I'm really happy to keep
     seeing this stuff.

   - Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.

   - Lots of cleanups and fixes in L2TP code from Guillaume Nault.

   - Add IPSEC offload support to netdevsim, from Shannon Nelson.

   - Add support for slotting with non-uniform distribution to netem
     packet scheduler, from Yousuk Seung.

   - Add UDP GSO support to mlx5e, from Boris Pismenny.

   - Support offloading of Team LAG in NFP, from John Hurley.

   - Allow to configure TX queue selection based upon RX queue, from
     Amritha Nambiar.

   - Support ethtool ring size configuration in aquantia, from Anton
     Mikaev.

   - Support DSCP and flowlabel per-transport in SCTP, from Xin Long.

   - Support list based batching and stack traversal of SKBs, this is
     very exciting work. From Edward Cree.

   - Busyloop optimizations in vhost_net, from Toshiaki Makita.

   - Introduce the ETF qdisc, which allows time based transmissions. IGB
     can offload this in hardware. From Vinicius Costa Gomes.

   - Add parameter support to devlink, from Moshe Shemesh.

   - Several multiplication and division optimizations for BPF JIT in
     nfp driver, from Jiong Wang.

   - Lots of prepatory work to make more of the packet scheduler layer
     lockless, when possible, from Vlad Buslov.

   - Add ACK filter and NAT awareness to sch_cake packet scheduler, from
     Toke Høiland-Jørgensen.

   - Support regions and region snapshots in devlink, from Alex Vesker.

   - Allow to attach XDP programs to both HW and SW at the same time on
     a given device, with initial support in nfp. From Jakub Kicinski.

   - Add TLS RX offload and support in mlx5, from Ilya Lesokhin.

   - Use PHYLIB in r8169 driver, from Heiner Kallweit.

   - All sorts of changes to support Spectrum 2 in mlxsw driver, from
     Ido Schimmel.

   - PTP support in mv88e6xxx DSA driver, from Andrew Lunn.

   - Make TCP_USER_TIMEOUT socket option more accurate, from Jon
     Maxwell.

   - Support for templates in packet scheduler classifier, from Jiri
     Pirko.

   - IPV6 support in RDS, from Ka-Cheong Poon.

   - Native tproxy support in nf_tables, from Máté Eckl.

   - Maintain IP fragment queue in an rbtree, but optimize properly for
     in-order frags. From Peter Oskolkov.

   - Improvde handling of ACKs on hole repairs, from Yuchung Cheng"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
  bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
  hv/netvsc: Fix NULL dereference at single queue mode fallback
  net: filter: mark expected switch fall-through
  xen-netfront: fix warn message as irq device name has '/'
  cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
  net: dsa: mv88e6xxx: missing unlock on error path
  rds: fix building with IPV6=m
  inet/connection_sock: prefer _THIS_IP_ to current_text_addr
  net: dsa: mv88e6xxx: bitwise vs logical bug
  net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
  ieee802154: hwsim: using right kind of iteration
  net: hns3: Add vlan filter setting by ethtool command -K
  net: hns3: Set tx ring' tc info when netdev is up
  net: hns3: Remove tx ring BD len register in hns3_enet
  net: hns3: Fix desc num set to default when setting channel
  net: hns3: Fix for phy link issue when using marvell phy driver
  net: hns3: Fix for information of phydev lost problem when down/up
  net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
  net: hns3: Add support for serdes loopback selftest
  bnxt_en: take coredump_record structure off stack
  ...

3 files changed, 242 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt
index 47a6a7fe0b86..1811e1972a7a 100644
--- a/Documentation/devicetree/bindings/net/dsa/b53.txt
+++ b/Documentation/devicetree/bindings/net/dsa/b53.txt
@@ -24,6 +24,14 @@ Required properties:
       "brcm,bcm53018-srab"
       "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string
 
+  For the BCM5831X/BCM1140x SoCs with an integrated switch, must be one of:
+      "brcm,bcm11404-srab"
+      "brcm,bcm11407-srab"
+      "brcm,bcm11409-srab"
+      "brcm,bcm58310-srab"
+      "brcm,bcm58311-srab"
+      "brcm,bcm58313-srab" and the mandatory "brcm,omega-srab" string
+
   For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of:
       "brcm,bcm58522-srab"
       "brcm,bcm58523-srab"
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
new file mode 100644
index 000000000000..b6ae8541bd55
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
@@ -0,0 +1,153 @@
+Realtek SMI-based Switches
+==========================
+
+The SMI "Simple Management Interface" is a two-wire protocol using
+bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
+not use the MDIO protocol. This binding defines how to specify the
+SMI-based Realtek devices.
+
+Required properties:
+
+- compatible: must be exactly one of:
+      "realtek,rtl8366"
+      "realtek,rtl8366rb" (4+1 ports)
+      "realtek,rtl8366s"  (4+1 ports)
+      "realtek,rtl8367"
+      "realtek,rtl8367b"
+      "realtek,rtl8368s"  (8 port)
+      "realtek,rtl8369"
+      "realtek,rtl8370"   (8 port)
+
+Required properties:
+- mdc-gpios: GPIO line for the MDC clock line.
+- mdio-gpios: GPIO line for the MDIO data line.
+- reset-gpios: GPIO line for the reset signal.
+
+Optional properties:
+- realtek,disable-leds: if the LED drivers are not used in the
+  hardware design this will disable them so they are not turned on
+  and wasting power.
+
+Required subnodes:
+
+- interrupt-controller
+
+  This defines an interrupt controller with an IRQ line (typically
+  a GPIO) that will demultiplex and handle the interrupt from the single
+  interrupt line coming out of one of the SMI-based chips. It most
+  importantly provides link up/down interrupts to the PHY blocks inside
+  the ASIC.
+
+Required properties of interrupt-controller:
+
+- interrupt: parent interrupt, see interrupt-controller/interrupts.txt
+- interrupt-controller: see interrupt-controller/interrupts.txt
+- #address-cells: should be <0>
+- #interrupt-cells: should be <1>
+
+- mdio
+
+  This defines the internal MDIO bus of the SMI device, mostly for the
+  purpose of being able to hook the interrupts to the right PHY and
+  the right PHY to the corresponding port.
+
+Required properties of mdio:
+
+- compatible: should be set to "realtek,smi-mdio" for all SMI devices
+
+See net/mdio.txt for additional MDIO bus properties.
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+switch {
+	compatible = "realtek,rtl8366rb";
+	/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+	mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+	mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+	reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+
+	switch_intc: interrupt-controller {
+		/* GPIO 15 provides the interrupt */
+		interrupt-parent = <&gpio0>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+	};
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+		port@0 {
+			reg = <0>;
+			label = "lan0";
+			phy-handle = <&phy0>;
+		};
+		port@1 {
+			reg = <1>;
+			label = "lan1";
+			phy-handle = <&phy1>;
+		};
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+			phy-handle = <&phy2>;
+		};
+		port@3 {
+			reg = <3>;
+			label = "lan3";
+			phy-handle = <&phy3>;
+		};
+		port@4 {
+			reg = <4>;
+			label = "wan";
+			phy-handle = <&phy4>;
+		};
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+
+	mdio {
+		compatible = "realtek,smi-mdio", "dsa-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: phy@0 {
+			reg = <0>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <0>;
+		};
+		phy1: phy@1 {
+			reg = <1>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <1>;
+		};
+		phy2: phy@2 {
+			reg = <2>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <2>;
+		};
+		phy3: phy@3 {
+			reg = <3>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <3>;
+		};
+		phy4: phy@4 {
+			reg = <4>;
+			interrupt-parent = <&switch_intc>;
+			interrupts = <12>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt
new file mode 100644
index 000000000000..ed4710c40641
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt
@@ -0,0 +1,81 @@
+Vitesse VSC73xx Switches
+========================
+
+This defines device tree bindings for the Vitesse VSC73xx switch chips.
+The Vitesse company has been acquired by Microsemi and Microsemi in turn
+acquired by Microchip but retains this vendor branding.
+
+The currently supported switch chips are:
+Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
+
+The device tree node is an SPI device so it must reside inside a SPI bus
+device tree node, see spi/spi-bus.txt
+
+Required properties:
+
+- compatible: must be exactly one of:
+	"vitesse,vsc7385"
+	"vitesse,vsc7388"
+	"vitesse,vsc7395"
+	"vitesse,vsc7398"
+- gpio-controller: indicates that this switch is also a GPIO controller,
+  see gpio/gpio.txt
+- #gpio-cells: this must be set to <2> and indicates that we are a twocell
+  GPIO controller, see gpio/gpio.txt
+
+Optional properties:
+
+- reset-gpios: a handle to a GPIO line that can issue reset of the chip.
+  It should be tagged as active low.
+
+Required subnodes:
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+switch@0 {
+	compatible = "vitesse,vsc7395";
+	reg = <0>;
+	/* Specified for 2.5 MHz or below */
+	spi-max-frequency = <2500000>;
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+		};
+		vsc: port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac1>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};