diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
121 files changed, 2416 insertions, 263 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic,scpi.txt b/Documentation/devicetree/bindings/arm/amlogic,scpi.txt new file mode 100644 index 000000000000..7b9a861e9306 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic,scpi.txt @@ -0,0 +1,20 @@ +System Control and Power Interface (SCPI) Message Protocol +(in addition to the standard binding in [0]) +---------------------------------------------------------- +Required properties + +- compatible : should be "amlogic,meson-gxbb-scpi" + +AMLOGIC SRAM and Shared Memory for SCPI +------------------------------------ + +Required properties: +- compatible : should be "amlogic,meson-gxbb-sram" + +Each sub-node represents the reserved area for SCPI. + +Required sub-node properties: +- compatible : should be "amlogic,meson-gxbb-scp-shmem" for SRAM based shared + memory on Amlogic GXBB SoC. + +[0] Documentation/devicetree/bindings/arm/arm,scpi.txt diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index fcc6f6c10803..9b2b41ab6817 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -17,6 +17,18 @@ Boards with the Amlogic Meson GXBaby SoC shall have the following properties: Required root node property: compatible: "amlogic,meson-gxbb"; +Boards with the Amlogic Meson GXL S905X SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s905x", "amlogic,meson-gxl"; + +Boards with the Amlogic Meson GXL S905D SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s905d", "amlogic,meson-gxl"; + +Boards with the Amlogic Meson GXM S912 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s912", "amlogic,meson-gxm"; + Board compatible values: - "geniatech,atv1200" (Meson6) - "minix,neo-x8" (Meson8) @@ -28,3 +40,10 @@ Board compatible values: - "hardkernel,odroid-c2" (Meson gxbb) - "amlogic,p200" (Meson gxbb) - "amlogic,p201" (Meson gxbb) + - "amlogic,p212" (Meson gxl s905x) + - "amlogic,p230" (Meson gxl s905d) + - "amlogic,p231" (Meson gxl s905d) + - "amlogic,q200" (Meson gxm s912) + - "amlogic,q201" (Meson gxm s912) + - "nexbox,a95x" (Meson gxbb or Meson gxl s905x) + - "nexbox,a1" (Meson gxm s912) diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt index faa4b44572e3..401831973638 100644 --- a/Documentation/devicetree/bindings/arm/arm,scpi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -7,7 +7,10 @@ by Linux to initiate various system control and power operations. Required properties: -- compatible : should be "arm,scpi" +- compatible : should be + * "arm,scpi" : For implementations complying to SCPI v1.0 or above + * "arm,scpi-pre-1.0" : For implementations complying to all + unversioned releases prior to SCPI v1.0 - mboxes: List of phandle and mailbox channel specifiers All the channels reserved by remote SCP firmware for use by SCPI message protocol should be specified in any order @@ -59,18 +62,14 @@ SRAM and Shared Memory for SCPI A small area of SRAM is reserved for SCPI communication between application processors and SCP. -Required properties: -- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM on Juno - -The rest of the properties should follow the generic mmio-sram description -found in ../../sram/sram.txt +The properties should follow the generic mmio-sram description found in [3] Each sub-node represents the reserved area for SCPI. Required sub-node properties: - reg : The base offset and size of the reserved area with the SRAM -- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based - shared memory on Juno platforms +- compatible : should be "arm,scp-shmem" for Non-secure SRAM based + shared memory Sensor bindings for the sensors based on SCPI Message Protocol -------------------------------------------------------------- @@ -81,11 +80,9 @@ Required properties: - #thermal-sensor-cells: should be set to 1. This property follows the thermal device tree bindings[2]. - Valid cell values are raw identifiers (Sensor - ID) as used by the firmware. Refer to - platform documentation for your - implementation for the IDs to use. For Juno - R0 and Juno R1 refer to [3]. + Valid cell values are raw identifiers (Sensor ID) + as used by the firmware. Refer to platform details + for your implementation for the IDs to use. Power domain bindings for the power domains based on SCPI Message Protocol ------------------------------------------------------------ @@ -112,7 +109,7 @@ Required properties: [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html [1] Documentation/devicetree/bindings/clock/clock-bindings.txt [2] Documentation/devicetree/bindings/thermal/thermal.txt -[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html +[3] Documentation/devicetree/bindings/sram/sram.txt [4] Documentation/devicetree/bindings/power/power_domain.txt Example: diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index ab318a56fca2..b6e810c2781a 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -148,11 +148,12 @@ Example: /dts-v1/; #include <dt-bindings/interrupt-controller/irq.h> -#include "skeleton.dtsi" / { model = "ARM RealView PB1176 with device tree"; compatible = "arm,realview-pb1176"; + #address-cells = <1>; + #size-cells = <1>; soc { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index e1f5ad855f14..29737b9b616e 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -225,3 +225,19 @@ required properties: compatible = "atmel,sama5d3-sfr", "syscon"; reg = <0xf0038000 0x60>; }; + +Security Module (SECUMOD) + +The Security Module macrocell provides all necessary secure functions to avoid +voltage, temperature, frequency and mechanical attacks on the chip. It also +embeds secure memories that can be scrambled + +required properties: +- compatible: Should be "atmel,<chip>-secumod", "syscon". + <chip> can be "sama5d2". +- reg: Should contain registers location and length + + secumod@fc040000 { + compatible = "atmel,sama5d2-secumod", "syscon"; + reg = <0xfc040000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/ns2.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt index 35f056f4a1c3..35f056f4a1c3 100644 --- a/Documentation/devicetree/bindings/arm/bcm/ns2.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,ns2.txt diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index c1dcf4cade2e..a1bcfeed5f24 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -178,6 +178,7 @@ nodes to be present and contain the properties described below. "marvell,pj4b" "marvell,sheeva-v5" "nvidia,tegra132-denver" + "nvidia,tegra186-denver" "qcom,krait" "qcom,kryo" "qcom,scorpion" diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index dbbc0952021c..d6ee9c6e1dbb 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -97,7 +97,7 @@ Freescale LS1021A Platform Device Tree Bindings Required root node compatible properties: - compatible = "fsl,ls1021a"; -Freescale LS1021A SoC-specific Device Tree Bindings +Freescale SoC-specific Device Tree Bindings ------------------------------------------- Freescale SCFG @@ -105,7 +105,11 @@ Freescale SCFG configuration and status registers for the chip. Such as getting PEX port status. Required properties: - - compatible: should be "fsl,ls1021a-scfg" + - compatible: Should contain a chip-specific compatible string, + Chip-specific strings are of the form "fsl,<chip>-scfg", + The following <chip>s are known to be supported: + ls1021a, ls1043a, ls1046a, ls2080a. + - reg: should contain base address and length of SCFG memory-mapped registers Example: @@ -119,7 +123,11 @@ Freescale DCFG configuration and status for the device. Such as setting the secondary core start address and release the secondary core from holdoff and startup. Required properties: - - compatible: should be "fsl,ls1021a-dcfg" + - compatible: Should contain a chip-specific compatible string, + Chip-specific strings are of the form "fsl,<chip>-dcfg", + The following <chip>s are known to be supported: + ls1021a, ls1043a, ls1046a, ls2080a. + - reg : should contain base address and length of DCFG memory-mapped registers Example: @@ -131,6 +139,10 @@ Example: Freescale ARMv8 based Layerscape SoC family Device Tree Bindings ---------------------------------------------------------------- +LS1043A SoC +Required root node properties: + - compatible = "fsl,ls1043a"; + LS1043A ARMv8 based RDB Board Required root node properties: - compatible = "fsl,ls1043a-rdb", "fsl,ls1043a"; @@ -139,6 +151,22 @@ LS1043A ARMv8 based QDS Board Required root node properties: - compatible = "fsl,ls1043a-qds", "fsl,ls1043a"; +LS1046A SoC +Required root node properties: + - compatible = "fsl,ls1046a"; + +LS1046A ARMv8 based QDS Board +Required root node properties: + - compatible = "fsl,ls1046a-qds", "fsl,ls1046a"; + +LS1046A ARMv8 based RDB Board +Required root node properties: + - compatible = "fsl,ls1046a-rdb", "fsl,ls1046a"; + +LS2080A SoC +Required root node properties: + - compatible = "fsl,ls2080a"; + LS2080A ARMv8 based Simulator model Required root node properties: - compatible = "fsl,ls2080a-simu", "fsl,ls2080a"; diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 3f81575aa6be..7df79a715611 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -28,6 +28,10 @@ HiP06 D03 Board Required root node properties: - compatible = "hisilicon,hip06-d03"; +HiP07 D05 Board +Required root node properties: + - compatible = "hisilicon,hip07-d05"; + Hisilicon system controller Required properties: diff --git a/Documentation/devicetree/bindings/arm/juno,scpi.txt b/Documentation/devicetree/bindings/arm/juno,scpi.txt new file mode 100644 index 000000000000..2ace8696bbee --- /dev/null +++ b/Documentation/devicetree/bindings/arm/juno,scpi.txt @@ -0,0 +1,26 @@ +System Control and Power Interface (SCPI) Message Protocol +(in addition to the standard binding in [0]) + +Juno SRAM and Shared Memory for SCPI +------------------------------------ + +Required properties: +- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM + +Each sub-node represents the reserved area for SCPI. + +Required sub-node properties: +- reg : The base offset and size of the reserved area with the SRAM +- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based + shared memory on Juno platforms + +Sensor bindings for the sensors based on SCPI Message Protocol +-------------------------------------------------------------- +Required properties: +- compatible : should be "arm,scpi-sensors". +- #thermal-sensor-cells: should be set to 1. + For Juno R0 and Juno R1 refer to [1] for the + sensor identifiers + +[0] Documentation/devicetree/bindings/arm/arm,scpi.txt +[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html diff --git a/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt new file mode 100644 index 000000000000..31f5f9a104cc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt @@ -0,0 +1,81 @@ +Texas Instruments System Control Interface (TI-SCI) Message Protocol +-------------------------------------------------------------------- + +Texas Instrument's processors including those belonging to Keystone generation +of processors have separate hardware entity which is now responsible for the +management of the System on Chip (SoC) system. These include various system +level functions as well. + +An example of such an SoC is K2G, which contains the system control hardware +block called Power Management Micro Controller (PMMC). This hardware block is +initialized early into boot process and provides services to Operating Systems +on multiple processors including ones running Linux. + +See http://processors.wiki.ti.com/index.php/TISCI for protocol definition. + +TI-SCI controller Device Node: +============================= + +The TI-SCI node describes the Texas Instrument's System Controller entity node. +This parent node may optionally have additional children nodes which describe +specific functionality such as clocks, power domain, reset or additional +functionality as may be required for the SoC. This hierarchy also describes the +relationship between the TI-SCI parent node to the child node. + +Required properties: +------------------- +- compatible: should be "ti,k2g-sci" +- mbox-names: + "rx" - Mailbox corresponding to receive path + "tx" - Mailbox corresponding to transmit path + +- mboxes: Mailboxes corresponding to the mbox-names. Each value of the mboxes + property should contain a phandle to the mailbox controller device + node and an args specifier that will be the phandle to the intended + sub-mailbox child node to be used for communication. + +See Documentation/devicetree/bindings/mailbox/mailbox.txt for more details +about the generic mailbox controller and client driver bindings. Also see +Documentation/devicetree/bindings/mailbox/ti,message-manager.txt for typical +controller that is used to communicate with this System controllers. + +Optional Properties: +------------------- +- reg-names: + debug_messages - Map the Debug message region +- reg: register space corresponding to the debug_messages +- ti,system-reboot-controller: If system reboot can be triggered by SoC reboot + +Example (K2G): +------------- + pmmc: pmmc { + compatible = "ti,k2g-sci"; + mbox-names = "rx", "tx"; + mboxes= <&msgmgr &msgmgr_proxy_pmmc_rx>, + <&msgmgr &msgmgr_proxy_pmmc_tx>; + reg-names = "debug_messages"; + reg = <0x02921800 0x800>; + }; + + +TI-SCI Client Device Node: +========================= + +Client nodes are maintained as children of the relevant TI-SCI device node. + +Example (K2G): +------------- + pmmc: pmmc { + compatible = "ti,k2g-sci"; + ... + + my_clk_node: clk_node { + ... + ... + }; + + my_pd_node: pd_node { + ... + ... + }; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index f53e2ee65e35..05f95c3ed7d4 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -86,6 +86,9 @@ SoCs: - DRA722 compatible = "ti,dra722", "ti,dra72", "ti,dra7" +- DRA718 + compatible = "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7" + - AM5728 compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" @@ -175,12 +178,18 @@ Boards: - AM5728 IDK compatible = "ti,am5728-idk", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM5718 IDK + compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7" + - DRA742 EVM: Software Development Board for DRA742 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7" - DRA722 EVM: Software Development Board for DRA722 compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7" +- DRA718 EVM: Software Development Board for DRA718 + compatible = "ti,dra718-evm", "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7" + - DM3730 Logic PD Torpedo + Wireless: Commercial System on Module with WiFi and Bluetooth compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt index b9e49711ba05..ac64e60f99f1 100644 --- a/Documentation/devicetree/bindings/arm/oxnas.txt +++ b/Documentation/devicetree/bindings/arm/oxnas.txt @@ -5,5 +5,10 @@ Boards with the OX810SE SoC shall have the following properties: Required root node property: compatible: "oxsemi,ox810se" +Boards with the OX820 SoC shall have the following properties: + Required root node property: + compatible: "oxsemi,ox820" + Board compatible values: - "wd,mbwe" (OX810SE) + - "cloudengines,pogoplugv3" (OX820) diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt index 3e24518c6678..028d16e72186 100644 --- a/Documentation/devicetree/bindings/arm/qcom.txt +++ b/Documentation/devicetree/bindings/arm/qcom.txt @@ -21,7 +21,10 @@ The 'SoC' element must be one of the following strings: apq8096 msm8916 msm8974 + msm8992 + msm8994 msm8996 + mdm9615 The 'board' element must be one of the following strings: diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 55f388f954de..cc4ace6397ab 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -25,6 +25,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "radxa,rock2-square", "rockchip,rk3288"; +- Rikomagic MK808 v1 board: + Required root node properties: + - compatible = "rikomagic,mk808", "rockchip,rk3066a"; + - Firefly Firefly-RK3288 board: Required root node properties: - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; @@ -99,6 +103,18 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "mqmaker,miqi", "rockchip,rk3288"; +- Rockchip PX3 Evaluation board: + Required root node properties: + - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188"; + +- Rockchip PX5 Evaluation board: + Required root node properties: + - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368"; + +- Rockchip RK1108 Evaluation board + Required root node properties: + - compatible = "rockchip,rk1108-evb", "rockchip,rk1108"; + - Rockchip RK3368 evb: Required root node properties: - compatible = "rockchip,rk3368-evb-act8846", "rockchip,rk3368"; diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14ef294..3c551894f621 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -15,6 +15,8 @@ Required root node properties: - "samsung,xyref5260" - for Exynos5260-based Samsung board. - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,tm2" - for Exynos5433-based Samsung TM2 board. + - "samsung,tm2e" - for Exynos5433-based Samsung TM2E board. - "samsung,sd5v1" - for Exynos5440-based Samsung board. - "samsung,ssdk5440" - for Exynos5440-based Samsung board. @@ -22,6 +24,9 @@ Required root node properties: * FriendlyARM - "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM TINY4412 board. + * TOPEET + - "topeet,itop4412-elite" - for Exynos4412-based TOPEET + Elite base board. * Google - "google,pi" - for Exynos5800-based Google Peach Pi diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 2f0b7169f132..253bf9b86690 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -13,6 +13,10 @@ SoCs: compatible = "renesas,r8a73a4" - R-Mobile A1 (R8A77400) compatible = "renesas,r8a7740" + - RZ/G1M (R8A77430) + compatible = "renesas,r8a7743" + - RZ/G1E (R8A77450) + compatible = "renesas,r8a7745" - R-Car M1A (R8A77781) compatible = "renesas,r8a7778" - R-Car H1 (R8A77790) @@ -35,7 +39,7 @@ SoCs: Boards: - - Alt + - Alt (RTP0RC7794SEB00010S) compatible = "renesas,alt", "renesas,r8a7794" - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" @@ -47,9 +51,9 @@ Boards: compatible = "renesas,bockw", "renesas,r8a7778" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - - Gose + - Gose (RTP0RC7793SEB00010S) compatible = "renesas,gose", "renesas,r8a7793" - - H3ULCB (RTP0RC7795SKB00010S) + - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKB00010S) compatible = "renesas,h3ulcb", "renesas,r8a7795"; - Henninger compatible = "renesas,henninger", "renesas,r8a7791" @@ -61,7 +65,9 @@ Boards: compatible = "renesas,kzm9g", "renesas,sh73a0" - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - - Marzen + - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKB00010S) + compatible = "renesas,m3ulcb", "renesas,r8a7796"; + - Marzen (R0P7779A00010S) compatible = "renesas,marzen", "renesas,r8a7779" - Porter (M2-LCDP) compatible = "renesas,porter", "renesas,r8a7791" @@ -73,5 +79,27 @@ Boards: compatible = "renesas,salvator-x", "renesas,r8a7796"; - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" + - SK-RZG1E (YR8A77450S000BE) + compatible = "renesas,sk-rzg1e", "renesas,r8a7745" + - SK-RZG1M (YR8A77430S000BE) + compatible = "renesas,sk-rzg1m", "renesas,r8a7743" - Wheat compatible = "renesas,wheat", "renesas,r8a7792" + + +Most Renesas ARM SoCs have a Product Register that allows to retrieve SoC +product and revision information. If present, a device node for this register +should be added. + +Required properties: + - compatible: Must be "renesas,prr". + - reg: Base address and length of the register block. + + +Examples +-------- + + prr: chipid@ff000044 { + compatible = "renesas,prr"; + reg = <0 0xff000044 0 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index 3975d0a0e4c2..4d6467cc2aa2 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -14,4 +14,5 @@ using one of the following compatible strings: allwinner,sun8i-a83t allwinner,sun8i-h3 allwinner,sun9i-a80 + allwinner,sun50i-a64 nextthing,gr8 diff --git a/Documentation/devicetree/bindings/arm/swir.txt b/Documentation/devicetree/bindings/arm/swir.txt new file mode 100644 index 000000000000..042be73a95d3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/swir.txt @@ -0,0 +1,12 @@ +Sierra Wireless Modules device tree bindings +-------------------------------------------- + +Supported Modules : + - WP8548 : Includes MDM9615 and PM8018 in a module + +Sierra Wireless modules shall have the following properties : + Required root node property + - compatible: "swir,wp8548" for the WP8548 CF3 Module + +Board compatible values: + - "swir,mangoh-green-wp8548" for the mangOH green board with the WP8548 module diff --git a/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt index 032a7606b862..fc33ca01e9ba 100644 --- a/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt +++ b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt @@ -3,7 +3,7 @@ Binding for Freescale QorIQ AHCI SATA Controller Required properties: - reg: Physical base address and size of the controller's register area. - compatible: Compatibility string. Must be 'fsl,<chip>-ahci', where - chip could be ls1021a, ls2080a, ls1043a etc. + chip could be ls1021a, ls1043a, ls1046a, ls2080a etc. - clocks: Input clock specifier. Refer to common clock bindings. - interrupts: Interrupt specifier. Refer to interrupt binding. diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt index e1d01df8e3c1..909c9935360d 100644 --- a/Documentation/devicetree/bindings/ata/ahci-st.txt +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -18,21 +18,6 @@ Optional properties: Example: - /* Example for stih416 */ - sata0: sata@fe380000 { - compatible = "st,ahci"; - reg = <0xfe380000 0x1000>; - interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; - interrupt-names = "hostc"; - phys = <&phy_port0 PHY_TYPE_SATA>; - phy-names = "ahci_phy"; - resets = <&powerdown STIH416_SATA0_POWERDOWN>, - <&softreset STIH416_SATA0_SOFTRESET>; - reset-names = "pwr-dwn", "sw-rst"; - clocks = <&clk_s_a0_ls CLK_ICN_REG>; - clock-names = "ahci_clk"; - }; - /* Example for stih407 family silicon */ sata0: sata@9b20000 { compatible = "st,ahci"; diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt new file mode 100644 index 000000000000..83b0e54f727c --- /dev/null +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt @@ -0,0 +1,132 @@ +Device tree bindings for NVIDIA Tegra Generic Memory Interface bus + +The Generic Memory Interface bus enables memory transfers between internal and +external memory. Can be used to attach various high speed devices such as +synchronous/asynchronous NOR, FPGA, UARTS and more. + +The actual devices are instantiated from the child nodes of a GMI node. + +Required properties: + - compatible : Should contain one of the following: + For Tegra20 must contain "nvidia,tegra20-gmi". + For Tegra30 must contain "nvidia,tegra30-gmi". + - reg: Should contain GMI controller registers location and length. + - clocks: Must contain an entry for each entry in clock-names. + - clock-names: Must include the following entries: "gmi" + - resets : Must contain an entry for each entry in reset-names. + - reset-names : Must include the following entries: "gmi" + - #address-cells: The number of cells used to represent physical base + addresses in the GMI address space. Should be 2. + - #size-cells: The number of cells used to represent the size of an address + range in the GMI address space. Should be 1. + - ranges: Must be set up to reflect the memory layout with three integer values + for each chip-select line in use (only one entry is supported, see below + comments): + <cs-number> <offset> <physical address of mapping> <size> + +Note that the GMI controller does not have any internal chip-select address +decoding, because of that chip-selects either need to be managed via software +or by employing external chip-select decoding logic. + +If external chip-select logic is used to support multiple devices it is assumed +that the devices use the same timing and so are probably the same type. It also +assumes that they can fit in the 256MB address range. In this case only one +child device is supported which represents the active chip-select line, see +examples for more insight. + +The chip-select number is decoded from the child nodes second address cell of +'ranges' property, if 'ranges' property is not present or empty chip-select will +then be decoded from the first cell of the 'reg' property. + +Optional child cs node properties: + + - nvidia,snor-data-width-32bit: Use 32bit data-bus, default is 16bit. + - nvidia,snor-mux-mode: Enable address/data MUX mode. + - nvidia,snor-rdy-active-before-data: Assert RDY signal one cycle before data. + If omitted it will be asserted with data. + - nvidia,snor-rdy-active-high: RDY signal is active high + - nvidia,snor-adv-active-high: ADV signal is active high + - nvidia,snor-oe-active-high: WE/OE signal is active high + - nvidia,snor-cs-active-high: CS signal is active high + + Note that there is some special handling for the timing values. + From Tegra TRM: + Programming 0 means 1 clock cycle: actual cycle = programmed cycle + 1 + + - nvidia,snor-muxed-width: Number of cycles MUX address/data asserted on the + bus. Valid values are 0-15, default is 1 + - nvidia,snor-hold-width: Number of cycles CE stays asserted after the + de-assertion of WR_N (in case of SLAVE/MASTER Request) or OE_N + (in case of MASTER Request). Valid values are 0-15, default is 1 + - nvidia,snor-adv-width: Number of cycles during which ADV stays asserted. + Valid values are 0-15, default is 1. + - nvidia,snor-ce-width: Number of cycles before CE is asserted. + Valid values are 0-15, default is 4 + - nvidia,snor-we-width: Number of cycles during which WE stays asserted. + Valid values are 0-15, default is 1 + - nvidia,snor-oe-width: Number of cycles during which OE stays asserted. + Valid values are 0-255, default is 1 + - nvidia,snor-wait-width: Number of cycles before READY is asserted. + Valid values are 0-255, default is 3 + +Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the +controllers with a simple-bus node since they are all connected to the same +chip-select (CS4), in this example external address decoding is provided: + +gmi@70090000 { + compatible = "nvidia,tegra20-gmi"; + reg = <0x70009000 0x1000>; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&tegra_car TEGRA20_CLK_NOR>; + clock-names = "gmi"; + resets = <&tegra_car 42>; + reset-names = "gmi"; + ranges = <4 0 0xd0000000 0xfffffff>; + + status = "okay"; + + bus@4,0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 4 0 0x40100>; + + nvidia,snor-mux-mode; + nvidia,snor-adv-active-high; + + can@0 { + reg = <0 0x100>; + ... + }; + + can@40000 { + reg = <0x40000 0x100>; + ... + }; + }; +}; + +Example with one SJA1000 CAN controller connected to the GMI bus +on CS4: + +gmi@70090000 { + compatible = "nvidia,tegra20-gmi"; + reg = <0x70009000 0x1000>; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&tegra_car TEGRA20_CLK_NOR>; + clock-names = "gmi"; + resets = <&tegra_car 42>; + reset-names = "gmi"; + ranges = <4 0 0xd0000000 0xfffffff>; + + status = "okay"; + + can@4,0 { + reg = <4 0 0x100>; + nvidia,snor-mux-mode; + nvidia,snor-adv-active-high; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt b/Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt new file mode 100644 index 000000000000..72daefc6b4a1 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments da8xx master peripheral + priority driver + +DA8XX SoCs feature a set of registers allowing to change the priority of all +peripherals classified as masters. + +Documentation: +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf + +Required properties: + +- compatible: "ti,da850-mstpri" - for da850 based boards +- reg: offset and length of the mstpri registers + +Example for da850-lcdk is shown below. + +mstpri { + compatible = "ti,da850-mstpri"; + reg = <0x14110 0x0c>; +}; diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt index 19df842c694f..8163d565f697 100644 --- a/Documentation/devicetree/bindings/clock/imx31-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -77,7 +77,7 @@ Examples: clks: ccm@53f80000{ compatible = "fsl,imx31-ccm"; reg = <0x53f80000 0x4000>; - interrupts = <0 31 0x04 0 53 0x04>; + interrupts = <31>, <53>; #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index 16a3ec433119..df9cb5ac5f72 100644 --- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -32,6 +32,9 @@ Required properties: * "fsl,b4420-clockgen" * "fsl,b4860-clockgen" * "fsl,ls1021a-clockgen" + * "fsl,ls1043a-clockgen" + * "fsl,ls1046a-clockgen" + * "fsl,ls2080a-clockgen" Chassis-version clock strings include: * "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks * "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index adeca34c5a33..10a425f451fc 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -123,6 +123,9 @@ PROPERTIES EXAMPLE + +iMX6QDL/SX requires four clocks + crypto@300000 { compatible = "fsl,sec-v4.0"; fsl,sec-era = <2>; @@ -139,6 +142,23 @@ EXAMPLE clock-names = "mem", "aclk", "ipg", "emi_slow"; }; + +iMX6UL does only require three clocks + + crypto: caam@2140000 { + compatible = "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2140000 0x3c000>; + ranges = <0 0x2140000 0x3c000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clks IMX6UL_CLK_CAAM_MEM>, + <&clks IMX6UL_CLK_CAAM_ACLK>, + <&clks IMX6UL_CLK_CAAM_IPG>; + clock-names = "mem", "aclk", "ipg"; + }; + ===================================================================== Job Ring (JR) Node diff --git a/Documentation/devicetree/bindings/dma/nbpfaxi.txt b/Documentation/devicetree/bindings/dma/nbpfaxi.txt index d5e2522b9ec1..d2e1e62e346a 100644 --- a/Documentation/devicetree/bindings/dma/nbpfaxi.txt +++ b/Documentation/devicetree/bindings/dma/nbpfaxi.txt @@ -23,6 +23,14 @@ Required properties #define NBPF_SLAVE_RQ_LEVEL 4 Optional properties: +- max-burst-mem-read: limit burst size for memory reads + (DMA_MEM_TO_MEM/DMA_MEM_TO_DEV) to this value, specified in bytes, rather + than using the maximum burst size allowed by the hardware's buffer size. +- max-burst-mem-write: limit burst size for memory writes + (DMA_DEV_TO_MEM/DMA_MEM_TO_MEM) to this value, specified in bytes, rather + than using the maximum burst size allowed by the hardware's buffer size. + If both max-burst-mem-read and max-burst-mem-write are set, DMA_MEM_TO_MEM + will use the lower value. You can use dma-channels and dma-requests as described in dma.txt, although they won't be used, this information is derived from the compatibility string. diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt index fd5618bd8fbc..55492c264d17 100644 --- a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt +++ b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt @@ -5,13 +5,13 @@ memcpy and memset capabilities. It has been designed for virtualized environments. Each HIDMA HW instance consists of multiple DMA channels. These channels -share the same bandwidth. The bandwidth utilization can be parititioned +share the same bandwidth. The bandwidth utilization can be partitioned among channels based on the priority and weight assignments. There are only two priority levels and 15 weigh assignments possible. Other parameters here determine how much of the system bus this HIDMA -instance can use like maximum read/write request and and number of bytes to +instance can use like maximum read/write request and number of bytes to read/write in a single burst. Main node required properties: @@ -47,12 +47,18 @@ When the OS is not in control of the management interface (i.e. it's a guest), the channel nodes appear on their own, not under a management node. Required properties: -- compatible: must contain "qcom,hidma-1.0" +- compatible: must contain "qcom,hidma-1.0" for initial HW or "qcom,hidma-1.1" +for MSI capable HW. - reg: Addresses for the transfer and event channel - interrupts: Should contain the event interrupt - desc-count: Number of asynchronous requests this channel can handle - iommus: required a iommu node +Optional properties for MSI: +- msi-parent : See the generic MSI binding described in + devicetree/bindings/interrupt-controller/msi.txt for a description of the + msi-parent property. + Example: Hypervisor OS configuration: diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 5f2ce669789a..3316a9c2e638 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -24,6 +24,7 @@ Required Properties: - "renesas,dmac-r8a7793" (R-Car M2-N) - "renesas,dmac-r8a7794" (R-Car E2) - "renesas,dmac-r8a7795" (R-Car H3) + - "renesas,dmac-r8a7796" (R-Car M3-W) - reg: base address and length of the registers block for the DMAC diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index 0f5583293c9c..4775c66f4508 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -27,6 +27,8 @@ Optional properties: that services interrupts for this device - is_private: The device channels should be marked as private and not for by the general purpose DMA channel allocator. False if not passed. +- multi-block: Multi block transfers supported by hardware. Array property with + one cell per channel. 0: not supported, 1 (default): supported. Example: diff --git a/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt new file mode 100644 index 000000000000..e821e16ad65b --- /dev/null +++ b/Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt @@ -0,0 +1,108 @@ +NVIDIA Tegra Boot and Power Management Processor (BPMP) + +The BPMP is a specific processor in Tegra chip, which is designed for +booting process handling and offloading the power management, clock +management, and reset control tasks from the CPU. The binding document +defines the resources that would be used by the BPMP firmware driver, +which can create the interprocessor communication (IPC) between the CPU +and BPMP. + +Required properties: +- name : Should be bpmp +- compatible + Array of strings + One of: + - "nvidia,tegra186-bpmp" +- mboxes : The phandle of mailbox controller and the mailbox specifier. +- shmem : List of the phandle of the TX and RX shared memory area that + the IPC between CPU and BPMP is based on. +- #clock-cells : Should be 1. +- #power-domain-cells : Should be 1. +- #reset-cells : Should be 1. + +This node is a mailbox consumer. See the following files for details of +the mailbox subsystem, and the specifiers implemented by the relevant +provider(s): + +- .../mailbox/mailbox.txt +- .../mailbox/nvidia,tegra186-hsp.txt + +This node is a clock, power domain, and reset provider. See the following +files for general documentation of those features, and the specifiers +implemented by this node: + +- .../clock/clock-bindings.txt +- <dt-bindings/clock/tegra186-clock.h> +- ../power/power_domain.txt +- <dt-bindings/power/tegra186-powergate.h> +- .../reset/reset.txt +- <dt-bindings/reset/tegra186-reset.h> + +The BPMP implements some services which must be represented by separate nodes. +For example, it can provide access to certain I2C controllers, and the I2C +bindings represent each I2C controller as a device tree node. Such nodes should +be nested directly inside the main BPMP node. + +Software can determine whether a child node of the BPMP node represents a device +by checking for a compatible property. Any node with a compatible property +represents a device that can be instantiated. Nodes without a compatible +property may be used to provide configuration information regarding the BPMP +itself, although no such configuration nodes are currently defined by this +binding. + +The BPMP firmware defines no single global name-/numbering-space for such +services. Put another way, the numbering scheme for I2C buses is distinct from +the numbering scheme for any other service the BPMP may provide (e.g. a future +hypothetical SPI bus service). As such, child device nodes will have no reg +property, and the BPMP node will have no #address-cells or #size-cells property. + +The shared memory bindings for BPMP +----------------------------------- + +The shared memory area for the IPC TX and RX between CPU and BPMP are +predefined and work on top of sysram, which is an SRAM inside the chip. + +See ".../sram/sram.txt" for the bindings. + +Example: + +hsp_top0: hsp@03c00000 { + ... + #mbox-cells = <2>; +}; + +sysram@30000000 { + compatible = "nvidia,tegra186-sysram", "mmio-sram"; + reg = <0x0 0x30000000 0x0 0x50000>; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0x0 0x0 0x30000000 0x0 0x50000>; + + cpu_bpmp_tx: shmem@4e000 { + compatible = "nvidia,tegra186-bpmp-shmem"; + reg = <0x0 0x4e000 0x0 0x1000>; + label = "cpu-bpmp-tx"; + pool; + }; + + cpu_bpmp_rx: shmem@4f000 { + compatible = "nvidia,tegra186-bpmp-shmem"; + reg = <0x0 0x4f000 0x0 0x1000>; + label = "cpu-bpmp-rx"; + pool; + }; +}; + +bpmp { + compatible = "nvidia,tegra186-bpmp"; + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB TEGRA_HSP_DB_MASTER_BPMP>; + shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + + i2c { + compatible = "..."; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index 3b4436e56865..20f26fbce875 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -10,8 +10,10 @@ Required properties: * "qcom,scm-apq8064" for APQ8064 platforms * "qcom,scm-msm8660" for MSM8660 platforms * "qcom,scm-msm8690" for MSM8690 platforms + * "qcom,scm-msm8996" for MSM8996 platforms * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc) - clocks: One to three clocks may be required based on compatible. + * No clock required for "qcom,scm-msm8996" * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960" * Core, iface, and bus clocks required for "qcom,scm" - clock-names: Must contain "core" for the core clock, "iface" for the interface diff --git a/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt new file mode 100644 index 000000000000..817a8d4bf903 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-fpga2sdram-bridge.txt @@ -0,0 +1,16 @@ +Altera FPGA To SDRAM Bridge Driver + +Required properties: +- compatible : Should contain "altr,socfpga-fpga2sdram-bridge" + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + fpga_bridge3: fpga-bridge@ffc25080 { + compatible = "altr,socfpga-fpga2sdram-bridge"; + reg = <0xffc25080 0x4>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt new file mode 100644 index 000000000000..f8e288c71b2d --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-freeze-bridge.txt @@ -0,0 +1,23 @@ +Altera Freeze Bridge Controller Driver + +The Altera Freeze Bridge Controller manages one or more freeze bridges. +The controller can freeze/disable the bridges which prevents signal +changes from passing through the bridge. The controller can also +unfreeze/enable the bridges which allows traffic to pass through the +bridge normally. + +Required properties: +- compatible : Should contain "altr,freeze-bridge-controller" +- regs : base address and size for freeze bridge module + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +Example: + freeze-controller@100000450 { + compatible = "altr,freeze-bridge-controller"; + regs = <0x1000 0x10>; + bridge-enable = <0>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt new file mode 100644 index 000000000000..6406f9337eeb --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-hps2fpga-bridge.txt @@ -0,0 +1,39 @@ +Altera FPGA/HPS Bridge Driver + +Required properties: +- regs : base address and size for AXI bridge module +- compatible : Should contain one of: + "altr,socfpga-lwhps2fpga-bridge", + "altr,socfpga-hps2fpga-bridge", or + "altr,socfpga-fpga2hps-bridge" +- resets : Phandle and reset specifier for this bridge's reset +- clocks : Clocks used by this module. + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup. + 1 if driver should enable bridge at startup. + Default is to leave bridge in its current state. + +Example: + fpga_bridge0: fpga-bridge@ff400000 { + compatible = "altr,socfpga-lwhps2fpga-bridge"; + reg = <0xff400000 0x100000>; + resets = <&rst LWHPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + bridge-enable = <0>; + }; + + fpga_bridge1: fpga-bridge@ff500000 { + compatible = "altr,socfpga-hps2fpga-bridge"; + reg = <0xff500000 0x10000>; + resets = <&rst HPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + bridge-enable = <1>; + }; + + fpga_bridge2: fpga-bridge@ff600000 { + compatible = "altr,socfpga-fpga2hps-bridge"; + reg = <0xff600000 0x100000>; + resets = <&rst FPGA2HPS_RESET>; + clocks = <&l4_main_clk>; + }; diff --git a/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt b/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt new file mode 100644 index 000000000000..2fd8e7a84734 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/altera-socfpga-a10-fpga-mgr.txt @@ -0,0 +1,19 @@ +Altera SOCFPGA Arria10 FPGA Manager + +Required properties: +- compatible : should contain "altr,socfpga-a10-fpga-mgr" +- reg : base address and size for memory mapped io. + - The first index is for FPGA manager register access. + - The second index is for writing FPGA configuration data. +- resets : Phandle and reset specifier for the device's reset. +- clocks : Clocks used by the device. + +Example: + + fpga_mgr: fpga-mgr@ffd03000 { + compatible = "altr,socfpga-a10-fpga-mgr"; + reg = <0xffd03000 0x100 + 0xffcfe400 0x20>; + clocks = <&l4_mp_clk>; + resets = <&rst FPGAMGR_RESET>; + }; diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index c3d016532d8e..30fd2201b3d4 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -17,7 +17,9 @@ Required properties: - #interrupt-cells: Specifies the number of cells needed to encode an interrupt source. - gpio-controller : Marks the device node as a gpio controller. -- #gpio-cells : Should be one. It is the pin number. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. See gpio.txt for possible + values. Example for a MMP platform: @@ -27,7 +29,7 @@ Example for a MMP platform: interrupts = <49>; interrupt-names = "gpio_mux"; gpio-controller; - #gpio-cells = <1>; + #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt new file mode 100644 index 000000000000..70c054a9a997 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -0,0 +1,20 @@ +* Freescale Low Power Inter IC (LPI2C) for i.MX + +Required properties: +- compatible : + - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8dv-lpi2c" for LPI2C compatible with the one integrated on i.MX8DV soc +- reg : address and length of the lpi2c master registers +- interrupt-parent : core interrupt controller +- interrupts : lpi2c interrupt +- clocks : lpi2c clock specifier + +Examples: + +lpi2c7: lpi2c7@40A50000 { + compatible = "fsl,imx8dv-lpi2c"; + reg = <0x40A50000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_LPI2C7>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 12b78ac507e9..d30f0b11d853 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -7,6 +7,7 @@ Required properties : compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required as shown in the example below. + For the Armada 3700, the compatible should be "marvell,armada-3700-i2c". Recommended properties : diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 239632a0d709..2b8bd33dbf8d 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -1,17 +1,25 @@ I2C for R-Car platforms Required properties: -- compatible: Must be one of - "renesas,i2c-rcar" - "renesas,i2c-r8a7778" - "renesas,i2c-r8a7779" - "renesas,i2c-r8a7790" - "renesas,i2c-r8a7791" - "renesas,i2c-r8a7792" - "renesas,i2c-r8a7793" - "renesas,i2c-r8a7794" - "renesas,i2c-r8a7795" - "renesas,i2c-r8a7796" +- compatible: + "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. + "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. + "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. + "renesas,i2c-r8a7791" if the device is a part of a R8A7791 SoC. + "renesas,i2c-r8a7792" if the device is a part of a R8A7792 SoC. + "renesas,i2c-r8a7793" if the device is a part of a R8A7793 SoC. + "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. + "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. + "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. + "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device. + "renesas,i2c-rcar" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. @@ -33,7 +41,7 @@ Examples : i2c0: i2c@e6508000 { #address-cells = <1>; #size-cells = <0>; - compatible = "renesas,i2c-r8a7791"; + compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c"; reg = <0 0xe6508000 0 0x40>; interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 214f94c25d37..7716acc55dec 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -1,8 +1,7 @@ Device tree configuration for Renesas IIC (sh_mobile) driver Required properties: -- compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback - Examples with soctypes are: +- compatible : - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) - "renesas,iic-r8a7790" (R-Car H2) @@ -12,6 +11,17 @@ Required properties: - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-sh73a0" (SH-Mobile AG5) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) + - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) + - "renesas,rmobile-iic" (generic device) + + When compatible with a generic R-Car version, nodes + must list the SoC-specific version corresponding to + the platform first followed by the generic R-Car + version. + + renesas,rmobile-iic must always follow. + - reg : address start and address range size of device - interrupts : interrupt of device - clocks : clock for device @@ -31,7 +41,8 @@ Pinctrl properties might be needed, too. See there. Example: iic0: i2c@e6500000 { - compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic", + "renesas,rmobile-iic"; reg = <0 0xe6500000 0 0x425>; interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_IIC0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index 5fa691e6f638..cee9d5055fa2 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -62,6 +62,9 @@ wants to support one of the below features, it should adapt the bindings below. "irq" and "wakeup" names are recognized by I2C core, other names are left to individual drivers. +- host-notify + device uses SMBus host notify protocol instead of interrupt line. + - multi-master states that there is another master active on this bus. The OS can use this information to adapt power management to keep the arbitration awake @@ -81,6 +84,11 @@ Binding may contain optional "interrupts" property, describing interrupts used by the device. I2C core will assign "irq" interrupt (or the very first interrupt if not using interrupt names) as primary interrupt for the slave. +Alternatively, devices supporting SMbus Host Notify, and connected to +adapters that support this feature, may use "host-notify" property. I2C +core will create a virtual interrupt for Host Notify and assign it as +primary interrupt for the slave. + Also, if device is marked as a wakeup source, I2C core will set up "wakeup" interrupt for the device. If "wakeup" interrupt name is not present in the binding, then primary interrupt will be used as wakeup interrupt. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index df720ca00fcf..cdd7b48826c3 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -138,6 +138,8 @@ nuvoton,npct501 i2c trusted platform module (TPM) nuvoton,npct601 i2c trusted platform module (TPM2) nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset +nxp,pcf2127 Real-time clock +nxp,pcf2129 Real-time clock nxp,pcf8563 Real-time clock/calendar nxp,pcf85063 Tiny Real-Time Clock oki,ml86v7667 OKI ML86V7667 video decoder @@ -167,4 +169,5 @@ ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor +winbond,w83793 Winbond/Nuvoton H/W Monitor winbond,wpct301 i2c trusted platform module (TPM) diff --git a/Documentation/devicetree/bindings/input/da9062-onkey.txt b/Documentation/devicetree/bindings/input/da9062-onkey.txt index ab0e0488fe92..5f9fbc68e58a 100644 --- a/Documentation/devicetree/bindings/input/da9062-onkey.txt +++ b/Documentation/devicetree/bindings/input/da9062-onkey.txt @@ -1,32 +1,47 @@ -* Dialog DA9062/63 OnKey Module +* Dialog DA9061/62/63 OnKey Module -This module is part of the DA9062/DA9063. For more details about entire -chips see Documentation/devicetree/bindings/mfd/da9062.txt and -Documentation/devicetree/bindings/mfd/da9063.txt +This module is part of the DA9061/DA9062/DA9063. For more details about entire +DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt +For DA9063 see Documentation/devicetree/bindings/mfd/da9063.txt -This module provides KEY_POWER, KEY_SLEEP and events. +This module provides the KEY_POWER event. Required properties: -- compatible: should be one of: - dlg,da9062-onkey - dlg,da9063-onkey +- compatible: should be one of the following valid compatible string lines: + "dlg,da9061-onkey", "dlg,da9062-onkey" + "dlg,da9062-onkey" + "dlg,da9063-onkey" Optional properties: - - dlg,disable-key-power : Disable power-down using a long key-press. If this +- dlg,disable-key-power : Disable power-down using a long key-press. If this entry exists the OnKey driver will remove support for the KEY_POWER key - press. If this entry does not exist then by default the key-press - triggered power down is enabled and the OnKey will support both KEY_POWER - and KEY_SLEEP. + press when triggered using a long press of the OnKey. -Example: - - pmic0: da9062@58 { +Example: DA9063 + pmic0: da9063@58 { onkey { compatible = "dlg,da9063-onkey"; dlg,disable-key-power; }; + }; + +Example: DA9062 + + pmic0: da9062@58 { + onkey { + compatible = "dlg,da9062-onkey"; + dlg,disable-key-power; + }; + }; + +Example: DA9061 using a fall-back compatible for the DA9062 onkey driver + pmic0: da9061@58 { + onkey { + compatible = "dlg,da9061-onkey", "dlg,da9062-onkey"; + dlg,disable-key-power; + }; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt index 853dff96dd9f..d4927c202aef 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt @@ -17,6 +17,8 @@ Optional properties: This value depends on the touch screen. - pre-charge-time: the touch screen need some time to precharge. This value depends on the touch screen. +- touchscreen-average-samples: Number of data samples which are averaged for + each read. Valid values are 1, 4, 8, 16 and 32. Example: tsc: tsc@02040000 { @@ -32,5 +34,6 @@ Example: xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; measure-delay-time = <0xfff>; pre-charge-time = <0xffff>; + touchscreen-average-samples = <32>; status = "okay"; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt index 820fee4b77b6..ce85ee508238 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -18,6 +18,8 @@ Optional properties: - touchscreen-inverted-y : See touchscreen.txt - touchscreen-swapped-x-y : See touchscreen.txt - silead,max-fingers : maximum number of fingers the touchscreen can detect +- vddio-supply : regulator phandle for controller VDDIO +- avdd-supply : regulator phandle for controller AVDD Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt index bccaa4e73045..537643e86f61 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -14,6 +14,9 @@ Optional properties for Touchscreens: - touchscreen-fuzz-pressure : pressure noise value of the absolute input device (arbitrary range dependent on the controller) + - touchscreen-average-samples : Number of data samples which are averaged + for each read (valid values dependent on the + controller) - touchscreen-inverted-x : X axis is inverted (boolean) - touchscreen-inverted-y : Y axis is inverted (boolean) - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt index 3e5b9793341f..8682ab6d4a50 100644 --- a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -8,8 +8,9 @@ This driver provides a simple power button event via an Interrupt. Required properties: - compatible: should be "ti,tps65217-pwrbutton" or "ti,tps65218-pwrbutton" -Required properties for TPS65218: +Required properties: - interrupts: should be one of the following + - <2>: For controllers compatible with tps65217 - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 Examples: @@ -17,6 +18,7 @@ Examples: &tps { tps65217-pwrbutton { compatible = "ti,tps65217-pwrbutton"; + interrupts = <2>; }; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt index 0dcb7c7d3e40..944657684d73 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt @@ -15,6 +15,9 @@ Properties: Second cell specifies the irq distribution mode to cores 0=Round Robin; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3 + The second cell in interrupts property is deprecated and may be ignored by + the kernel. + intc accessed via the special ARC AUX register interface, hence "reg" property is not specified. diff --git a/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt index e893615ef635..b48d7d30012c 100644 --- a/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt +++ b/Documentation/devicetree/bindings/mailbox/brcm,bcm2835-mbox.txt @@ -12,7 +12,7 @@ Required properties: Example: -mailbox: mailbox@7e00b800 { +mailbox: mailbox@7e00b880 { compatible = "brcm,bcm2835-mbox"; reg = <0x7e00b880 0x40>; interrupts = <0 1>; diff --git a/Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt b/Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt new file mode 100644 index 000000000000..b99d25fc2f26 --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt @@ -0,0 +1,52 @@ +NVIDIA Tegra Hardware Synchronization Primitives (HSP) + +The HSP modules are used for the processors to share resources and communicate +together. It provides a set of hardware synchronization primitives for +interprocessor communication. So the interprocessor communication (IPC) +protocols can use hardware synchronization primitives, when operating between +two processors not in an SMP relationship. + +The features that HSP supported are shared mailboxes, shared semaphores, +arbitrated semaphores and doorbells. + +Required properties: +- name : Should be hsp +- compatible + Array of strings. + one of: + - "nvidia,tegra186-hsp" +- reg : Offset and length of the register set for the device. +- interrupt-names + Array of strings. + Contains a list of names for the interrupts described by the interrupt + property. May contain the following entries, in any order: + - "doorbell" + Users of this binding MUST look up entries in the interrupt property + by name, using this interrupt-names property to do so. +- interrupts + Array of interrupt specifiers. + Must contain one entry per entry in the interrupt-names property, + in a matching order. +- #mbox-cells : Should be 2. + +The mbox specifier of the "mboxes" property in the client node should +contain two data. The first one should be the HSP type and the second +one should be the ID that the client is going to use. Those information +can be found in the following file. + +- <dt-bindings/mailbox/tegra186-hsp.h>. + +Example: + +hsp_top0: hsp@3c00000 { + compatible = "nvidia,tegra186-hsp"; + reg = <0x0 0x03c00000 0x0 0xa0000>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "doorbell"; + #mbox-cells = <2>; +}; + +client { + ... + mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB TEGRA_HSP_DB_MASTER_XXX>; +}; diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt index 5fe9372abb37..26ca25b6d264 100644 --- a/Documentation/devicetree/bindings/media/exynos5-gsc.txt +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -3,7 +3,8 @@ G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs. Required properties: -- compatible: should be "samsung,exynos5-gsc" +- compatible: should be "samsung,exynos5-gsc" (for Exynos 5250, 5420 and + 5422 SoCs) or "samsung,exynos5433-gsc" (Exynos 5433) - reg: should contain G-Scaler physical address location and length. - interrupts: should contain G-Scaler interrupt number diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt index fb5e7606643a..54e1bede6244 100644 --- a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -8,10 +8,11 @@ Required properties: the device. The interrupt specifier format depends on the interrupt controller parent. - clocks: clock phandle and specifier pair. - - hisilicon,power-syscon: phandle of syscon used to control power. Optional properties: - linux,rc-map-name : Remote control map name. + - hisilicon,power-syscon: DEPRECATED. Don't use this in new dts files. + Provide correct clocks instead. Example node: @@ -19,7 +20,6 @@ Example node: compatible = "hisilicon,hix5hd2-ir"; reg = <0xf8001000 0x1000>; interrupts = <0 47 4>; - clocks = <&clock HIX5HD2_FIXED_24M>; - hisilicon,power-syscon = <&sysctrl>; + clocks = <&clock HIX5HD2_IR_CLOCK>; linux,rc-map-name = "rc-tivo"; }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index 8337f75c75da..9cbd92eb5d05 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -34,6 +34,7 @@ The digital output port node must contain at least one endpoint. Optional Properties: - reset-gpios: Reference to the GPIO connected to the device's reset pin. + - default-input: Select which input is selected after reset. Optional Endpoint Properties: @@ -47,8 +48,6 @@ Optional Endpoint Properties: If none of hsync-active, vsync-active and pclk-sample is specified the endpoint will use embedded BT.656 synchronization. - - default-input: Select which input is selected after reset. - Example: hdmi_receiver@4c { diff --git a/Documentation/devicetree/bindings/media/mediatek-mdp.txt b/Documentation/devicetree/bindings/media/mediatek-mdp.txt new file mode 100644 index 000000000000..4182063a54db --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-mdp.txt @@ -0,0 +1,109 @@ +* Mediatek Media Data Path + +Media Data Path is used for scaling and color space conversion. + +Required properties (controller (parent) node): +- compatible: "mediatek,mt8173-mdp" +- mediatek,vpu: the node of video processor unit, see + Documentation/devicetree/bindings/media/mediatek-vpu.txt for details. + +Required properties (all function blocks, child node): +- compatible: Should be one of + "mediatek,mt8173-mdp-rdma" - read DMA + "mediatek,mt8173-mdp-rsz" - resizer + "mediatek,mt8173-mdp-wdma" - write DMA + "mediatek,mt8173-mdp-wrot" - write DMA with rotation +- reg: Physical base address and length of the function block register space +- clocks: device clocks, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- power-domains: a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. + +Required properties (DMA function blocks, child node): +- compatible: Should be one of + "mediatek,mt8173-mdp-rdma" + "mediatek,mt8173-mdp-wdma" + "mediatek,mt8173-mdp-wrot" +- iommus: should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,larb: must contain the local arbiters in the current Socs, see + Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt + for details. + +Example: +mdp { + compatible = "mediatek,mt8173-mdp"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + mediatek,vpu = <&vpu>; + + mdp_rdma0: rdma@14001000 { + compatible = "mediatek,mt8173-mdp-rdma"; + reg = <0 0x14001000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA0>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA0>; + mediatek,larb = <&larb0>; + }; + + mdp_rdma1: rdma@14002000 { + compatible = "mediatek,mt8173-mdp-rdma"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RDMA1>, + <&mmsys CLK_MM_MUTEX_32K>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_RDMA1>; + mediatek,larb = <&larb4>; + }; + + mdp_rsz0: rsz@14003000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14003000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ0>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz1: rsz@14004000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14004000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ1>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_rsz2: rsz@14005000 { + compatible = "mediatek,mt8173-mdp-rsz"; + reg = <0 0x14005000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_RSZ2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + }; + + mdp_wdma0: wdma@14006000 { + compatible = "mediatek,mt8173-mdp-wdma"; + reg = <0 0x14006000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WDMA>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WDMA>; + mediatek,larb = <&larb0>; + }; + + mdp_wrot0: wrot@14007000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14007000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT0>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT0>; + mediatek,larb = <&larb0>; + }; + + mdp_wrot1: wrot@14008000 { + compatible = "mediatek,mt8173-mdp-wrot"; + reg = <0 0x14008000 0 0x1000>; + clocks = <&mmsys CLK_MM_MDP_WROT1>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + iommus = <&iommu M4U_PORT_MDP_WROT1>; + mediatek,larb = <&larb4>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 59a47a5b924b..46c15c54175d 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -1,25 +1,74 @@ Mediatek Video Codec Mediatek Video Codec is the video codec hw present in Mediatek SoCs which -supports high resolution encoding functionalities. +supports high resolution encoding and decoding functionalities. Required properties: - compatible : "mediatek,mt8173-vcodec-enc" for encoder + "mediatek,mt8173-vcodec-dec" for decoder. - reg : Physical base address of the video codec registers and length of memory mapped region. - interrupts : interrupt number to the cpu. - mediatek,larb : must contain the local arbiters in the current Socs. - clocks : list of clock specifiers, corresponding to entries in the clock-names property. -- clock-names: encoder must contain "venc_sel_src", "venc_sel", -- "venc_lt_sel_src", "venc_lt_sel". +- clock-names: encoder must contain "venc_sel_src", "venc_sel",, + "venc_lt_sel_src", "venc_lt_sel", decoder must contain "vcodecpll", + "univpll_d2", "clk_cci400_sel", "vdec_sel", "vdecpll", "vencpll", + "venc_lt_sel", "vdec_bus_clk_src". - iommus : should point to the respective IOMMU block with master port as argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt for details. - mediatek,vpu : the node of video processor unit + Example: -vcodec_enc: vcodec@0x18002000 { + +vcodec_dec: vcodec@16000000 { + compatible = "mediatek,mt8173-vcodec-dec"; + reg = <0 0x16000000 0 0x100>, /*VDEC_SYS*/ + <0 0x16020000 0 0x1000>, /*VDEC_MISC*/ + <0 0x16021000 0 0x800>, /*VDEC_LD*/ + <0 0x16021800 0 0x800>, /*VDEC_TOP*/ + <0 0x16022000 0 0x1000>, /*VDEC_CM*/ + <0 0x16023000 0 0x1000>, /*VDEC_AD*/ + <0 0x16024000 0 0x1000>, /*VDEC_AV*/ + <0 0x16025000 0 0x1000>, /*VDEC_PP*/ + <0 0x16026800 0 0x800>, /*VP8_VD*/ + <0 0x16027000 0 0x800>, /*VP6_VD*/ + <0 0x16027800 0 0x800>, /*VP8_VL*/ + <0 0x16028400 0 0x400>; /*VP9_VD*/ + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb1>; + iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>, + <&iommu M4U_PORT_HW_VDEC_PP_EXT>, + <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_RD_EXT>, + <&iommu M4U_PORT_HW_VDEC_PRED_WR_EXT>, + <&iommu M4U_PORT_HW_VDEC_UFO_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD_EXT>, + <&iommu M4U_PORT_HW_VDEC_VLD2_EXT>; + mediatek,vpu = <&vpu>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>; + clocks = <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&topckgen CLK_TOP_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>, + <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_VCODECPLL_370P5>; + clock-names = "vcodecpll", + "univpll_d2", + "clk_cci400_sel", + "vdec_sel", + "vdecpll", + "vencpll", + "venc_lt_sel", + "vdec_bus_clk_src"; + }; + + vcodec_enc: vcodec@0x18002000 { compatible = "mediatek,mt8173-vcodec-enc"; reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt index 27f9b8e459ac..3ec91803ba58 100644 --- a/Documentation/devicetree/bindings/media/renesas,fcp.txt +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -11,15 +11,9 @@ are paired with. These DT bindings currently support the FCPV and FCPF. - compatible: Must be one or more of the following - - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP' - - "renesas,r8a7795-fcpf" for R8A7795 (R-Car H3) compatible 'FCP for FDP' - "renesas,fcpv" for generic compatible 'FCP for VSP' - "renesas,fcpf" for generic compatible 'FCP for FDP' - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first, followed by the - family-specific and/or generic versions. - - reg: the register base and size for the device registers - clocks: Reference to the functional clock @@ -32,7 +26,7 @@ Device node example ------------------- fcpvd1: fcp@fea2f000 { - compatible = "renesas,r8a7795-fcpv", "renesas,fcpv"; + compatible = "renesas,fcpv"; reg = <0 0xfea2f000 0 0x200>; clocks = <&cpg CPG_MOD 602>; power-domains = <&sysc R8A7795_PD_A3VP>; diff --git a/Documentation/devicetree/bindings/media/renesas,fdp1.txt b/Documentation/devicetree/bindings/media/renesas,fdp1.txt new file mode 100644 index 000000000000..8dd1007bb573 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fdp1.txt @@ -0,0 +1,37 @@ +Renesas R-Car Fine Display Processor (FDP1) +------------------------------------------- + +The FDP1 is a de-interlacing module which converts interlaced video to +progressive video. It is capable of performing pixel format conversion between +YCbCr/YUV formats and RGB formats. Only YCbCr/YUV formats are supported as +an input to the module. + +Required properties: + + - compatible: must be "renesas,fdp1" + - reg: the register base and size for the device registers + - interrupts : interrupt specifier for the FDP1 instance + - clocks: reference to the functional clock + +Optional properties: + + - power-domains: reference to the power domain that the FDP1 belongs to, if + any. + - renesas,fcp: a phandle referencing the FCP that handles memory accesses + for the FDP1. Not needed on Gen2, mandatory on Gen3. + +Please refer to the binding documentation for the clock and/or power domain +providers for more details. + + +Device node example +------------------- + + fdp1@fe940000 { + compatible = "renesas,fdp1"; + reg = <0 0xfe940000 0 0x2400>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 119>; + power-domains = <&sysc R8A7795_PD_A3VP>; + renesas,fcp = <&fcpf0>; + }; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index 92c94f5ecbf1..2c901286d818 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -12,6 +12,7 @@ Required properties: (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs (c) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC (d) "samsung,mfc-v8" for MFC v8 present in Exynos5800 SoC + (e) "samsung,exynos5433-mfc" for MFC v8 present in Exynos5433 SoC - reg : Physical base address of the IP registers and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt new file mode 100644 index 000000000000..ec1dd408d573 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments da8xx DDR2/mDDR memory controller + +The DDR2/mDDR memory controller present on Texas Instruments da8xx SoCs features +a set of registers which allow to tweak the controller's behavior. + +Documentation: +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf + +Required properties: + +- compatible: "ti,da850-ddr-controller" - for da850 SoC based boards +- reg: a tuple containing the base address of the memory + controller and the size of the memory area to map + +Example for da850 shown below. + +ddrctl { + compatible = "ti,da850-ddr-controller"; + reg = <0xb0000000 0xe8>; +}; diff --git a/Documentation/devicetree/bindings/mfd/altera-a10sr.txt b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt new file mode 100644 index 000000000000..ea151f295ad7 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/altera-a10sr.txt @@ -0,0 +1,46 @@ +* Altera Arria10 Development Kit System Resource Chip + +Required parent device properties: +- compatible : "altr,a10sr" +- spi-max-frequency : Maximum SPI frequency. +- reg : The SPI Chip Select address for the Arria10 + System Resource chip +- interrupt-parent : The parent interrupt controller. +- interrupts : The interrupt line the device is connected to. +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + +The A10SR consists of these sub-devices: + +Device Description +------ ---------- +a10sr_gpio GPIO Controller + +Arria10 GPIO +Required Properties: +- compatible : Should be "altr,a10sr-gpio" +- gpio-controller : Marks the device node as a GPIO Controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + +Example: + + resource-manager@0 { + compatible = "altr,a10sr"; + reg = <0>; + spi-max-frequency = <100000>; + interrupt-parent = <&portb>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + a10sr_gpio: gpio-controller { + compatible = "altr,a10sr-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt index 37a088f9a648..9e5eba4a4f0d 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -10,6 +10,7 @@ voltages and other various functionality to Qualcomm SoCs. Value type: <string> Definition: must be one of: "qcom,pm8058" + "qcom,pm8821" "qcom,pm8921" - #address-cells: diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 9e6770b105c9..65c23263cc54 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,21 +1,25 @@ * Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T567/RN5T618 is a power management IC family which integrates -3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and -a watchdog timer. The RN5T618 provides additionally a Li-ion battery -charger, fuel gauge and an ADC. It can be controlled through an I2C -interface. +Ricoh RN5T567/RN5T618/RC5T619 is a power management IC family which +integrates 3 to 5 step-down DCDC converters, 7 to 10 low-dropout regulators, +GPIOs, and a watchdog timer. It can be controlled through an I2C interface. +The RN5T618/RC5T619 provides additionally a Li-ion battery charger, +fuel gauge, and an ADC. +The RC5T619 additionnally includes USB charger detection and an RTC. Required properties: - compatible: must be one of "ricoh,rn5t567" "ricoh,rn5t618" + "ricoh,rc5t619" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 - (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + (RN5T567/RC5T619), LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, LDO8, + LDO9, LDO10, LDORTC1 and LDORTC2. + LDO7-10 are specific to RC5T619. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 07184e8f894e..ea9c1c9607f6 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -13,6 +13,7 @@ Required Properties: - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following, before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 + - "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt index 750374fc9d94..c0f37cb41a9b 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt @@ -1,7 +1,9 @@ * Cadence SD/SDIO/eMMC Host Controller Required properties: -- compatible: should be "cdns,sd4hc". +- compatible: should be one of the following: + "cdns,sd4hc" - default of the IP + "socionext,uniphier-sd4hc" - for Socionext UniPhier SoCs - reg: offset and length of the register set for the device. - interrupts: a single interrupt specifier. - clocks: phandle to the input clock. @@ -19,7 +21,7 @@ if supported. See mmc.txt for details. Example: emmc: sdhci@5a000000 { - compatible = "cdns,sd4hc"; + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; reg = <0x5a000000 0x400>; interrupts = <0 78 4>; clocks = <&clk 4>; diff --git a/Documentation/devicetree/bindings/mtd/oxnas-nand.txt b/Documentation/devicetree/bindings/mtd/oxnas-nand.txt new file mode 100644 index 000000000000..56d5c19da41d --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/oxnas-nand.txt @@ -0,0 +1,41 @@ +* Oxford Semiconductor OXNAS NAND Controller + +Please refer to nand.txt for generic information regarding MTD NAND bindings. + +Required properties: + - compatible: "oxsemi,ox820-nand" + - reg: Base address and length for NAND mapped memory. + +Optional Properties: + - clocks: phandle to the NAND gate clock if needed. + - resets: phandle to the NAND reset control if needed. + +Example: + +nandc: nand-controller@41000000 { + compatible = "oxsemi,ox820-nand"; + reg = <0x41000000 0x100000>; + clocks = <&stdclk CLK_820_NAND>; + resets = <&reset RESET_NAND>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "hamming"; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x00e00000>; + read-only; + }; + + partition@e00000 { + label = "ubi"; + reg = <0x00e00000 0x07200000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt b/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt new file mode 100644 index 000000000000..0040eb8895e0 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/samsung-s3c2410.txt @@ -0,0 +1,56 @@ +* Samsung S3C2410 and compatible NAND flash controller + +Required properties: +- compatible : The possible values are: + "samsung,s3c2410-nand" + "samsung,s3c2412-nand" + "samsung,s3c2440-nand" +- reg : register's location and length. +- #address-cells, #size-cells : see nand.txt +- clocks : phandle to the nand controller clock +- clock-names : must contain "nand" + +Optional child nodes: +Child nodes representing the available nand chips. + +Optional child properties: +- nand-ecc-mode : see nand.txt +- nand-on-flash-bbt : see nand.txt + +Each child device node may optionally contain a 'partitions' sub-node, +which further contains sub-nodes describing the flash partition mapping. +See partition.txt for more detail. + +Example: + +nand-controller@4e000000 { + compatible = "samsung,s3c2440-nand"; + reg = <0x4e000000 0x40>; + + #address-cells = <1>; + #size-cells = <0>; + + clocks = <&clocks HCLK_NAND>; + clock-names = "nand"; + + nand { + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0 0x040000>; + }; + + partition@40000 { + label = "kernel"; + reg = <0x040000 0x500000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/tango-nand.txt b/Documentation/devicetree/bindings/mtd/tango-nand.txt new file mode 100644 index 000000000000..cd1bf2ac9055 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/tango-nand.txt @@ -0,0 +1,38 @@ +Sigma Designs Tango4 NAND Flash Controller (NFC) + +Required properties: + +- compatible: "sigma,smp8758-nand" +- reg: address/size of nfc_reg, nfc_mem, and pbus_reg +- dmas: reference to the DMA channel used by the controller +- dma-names: "rxtx" +- clocks: reference to the system clock +- #address-cells: <1> +- #size-cells: <0> + +Children nodes represent the available NAND chips. +See Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. + +Example: + + nandc: nand-controller@2c000 { + compatible = "sigma,smp8758-nand"; + reg = <0x2c000 0x30>, <0x2d000 0x800>, <0x20000 0x1000>; + dmas = <&dma0 3>; + dma-names = "rxtx"; + clocks = <&clkgen SYS_CLK>; + #address-cells = <1>; + #size-cells = <0>; + + nand@0 { + reg = <0>; /* CS0 */ + nand-ecc-strength = <14>; + nand-ecc-step-size = <1024>; + }; + + nand@1 { + reg = <1>; /* CS1 */ + nand-ecc-strength = <14>; + nand-ecc-step-size = <1024>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt index 063c02da018a..eea73adc678f 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt @@ -2,11 +2,14 @@ Hisilicon hix5hd2 gmac controller Required properties: - compatible: should contain one of the following SoC strings: - * "hisilicon,hix5hd2-gemac" - * "hisilicon,hi3798cv200-gemac" + * "hisilicon,hix5hd2-gmac" + * "hisilicon,hi3798cv200-gmac" + * "hisilicon,hi3516a-gmac" and one of the following version string: - * "hisilicon,hisi-gemac-v1" - * "hisilicon,hisi-gemac-v2" + * "hisilicon,hisi-gmac-v1" + * "hisilicon,hisi-gmac-v2" + The version v1 includes SoCs hix5hd2. + The version v2 includes SoCs hi3798cv200, hi3516a. - reg: specifies base physical address(s) and size of the device registers. The first region is the MAC register base and size. The second region is external interface control register. @@ -35,7 +38,7 @@ Required properties: Example: gmac0: ethernet@f9840000 { - compatible = "hisilicon,hi3798cv200-gemac", "hisilicon,hisi-gemac-v2"; + compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2"; reg = <0xf9840000 0x1000>,<0xf984300c 0x4>; interrupts = <0 71 4>; #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index c010fafc66a8..c7194e87d5f4 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -7,7 +7,7 @@ have dual GMAC each represented by a child node.. * Ethernet controller node Required properties: -- compatible: Should be "mediatek,mt7623-eth" +- compatible: Should be "mediatek,mt2701-eth" - reg: Address and length of the register set for the device - interrupts: Should contain the three frame engines interrupts in numeric order. These are fe_int0, fe_int1 and fe_int2. diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 54749b60a466..fb5056b22685 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -19,8 +19,9 @@ Optional Properties: specifications. If neither of these are specified, the default is to assume clause 22. - If the phy's identifier is known then the list may contain an entry - of the form: "ethernet-phy-idAAAA.BBBB" where + If the PHY reports an incorrect ID (or none at all) then the + "compatible" list may contain an entry with the correct PHY ID in the + form: "ethernet-phy-idAAAA.BBBB" where AAAA - The value of the 16 bit Phy Identifier 1 register as 4 hex digits. This is the chip vendor OUI bits 3:18 BBBB - The value of the 16 bit Phy Identifier 2 register as @@ -38,8 +39,14 @@ Optional Properties: - enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to compensate for the board being designed with the lanes swapped. -- eee-broken-modes: Bits to clear in the MDIO_AN_EEE_ADV register to - disable EEE broken modes. +- eee-broken-100tx: +- eee-broken-1000t: +- eee-broken-10gt: +- eee-broken-1000kx: +- eee-broken-10gkx4: +- eee-broken-10gkr: + Mark the corresponding energy efficient ethernet mode as broken and + request the ethernet to stop advertising it. Example: diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 85bf945b898f..afe9630a5e7d 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -3,9 +3,11 @@ Required properties: - reg - The ID number for the phy, usually a small integer - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable values diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt index 01b88f4e0d5b..b8e48b4762b2 100644 --- a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -1,10 +1,17 @@ * Broadcom iProc PCIe controller with the platform bus interface Required properties: -- compatible: Must be "brcm,iproc-pcie" for PAXB, or "brcm,iproc-pcie-paxc" - for PAXC. PAXB-based root complex is used for external endpoint devices. - PAXC-based root complex is connected to emulated endpoint devices - internal to the ASIC +- compatible: + "brcm,iproc-pcie" for the first generation of PAXB based controller, +used in SoCs including NSP, Cygnus, NS2, and Pegasus + "brcm,iproc-pcie-paxb-v2" for the second generation of PAXB-based +controllers, used in Stingray + "brcm,iproc-pcie-paxc" for the first generation of PAXC based +controller, used in NS2 + "brcm,iproc-pcie-paxc-v2" for the second generation of PAXC based +controller, used in Stingray + PAXB-based root complex is used for external endpoint devices. PAXC-based +root complex is connected to emulated endpoint devices internal to the ASIC - reg: base address and length of the PCIe controller I/O register space - #interrupt-cells: set to <1> - interrupt-map-mask and interrupt-map, standard PCI properties to define the @@ -19,6 +26,10 @@ Required properties: Optional properties: - phys: phandle of the PCIe PHY device - phy-names: must be "pcie-phy" +- dma-coherent: present if DMA operations are coherent +- dma-ranges: Some PAXB-based root complexes do not have inbound mapping done + by the ASIC after power on reset. In this case, SW is required to configure +the mapping, based on inbound memory regions specified by this property. - brcm,pcie-ob: Some iProc SoCs do not have the outbound address mapping done by the ASIC after power on reset. In this case, SW needs to configure it @@ -29,11 +40,6 @@ effective: Required: - brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal address used by the iProc PCIe core (not the PCIe address) -- brcm,pcie-ob-window-size: The outbound address mapping window size (in MB) - -Optional: -- brcm,pcie-ob-oarr-size: Some iProc SoCs need the OARR size bit to be set to -increase the outbound window size MSI support (optional): @@ -41,10 +47,19 @@ For older platforms without MSI integrated in the GIC, iProc PCIe core provides an event queue based MSI support. The iProc MSI uses host memories to store MSI posted writes in the event queues -- msi-parent: Link to the device node of the MSI controller. On newer iProc -platforms, the MSI controller may be gicv2m or gicv3-its. On older iProc -platforms without MSI support in its interrupt controller, one may use the -event queue based MSI support integrated within the iProc PCIe core. +On newer iProc platforms, gicv2m or gicv3-its based MSI support should be used + +- msi-map: Maps a Requester ID to an MSI controller and associated MSI +sideband data + +- msi-parent: Link to the device node of the MSI controller, used when no MSI +sideband data is passed between the iProc PCIe controller and the MSI +controller + +Refer to the following binding documents for more detailed description on +the use of 'msi-map' and 'msi-parent': + Documentation/devicetree/bindings/pci/pci-msi.txt + Documentation/devicetree/bindings/interrupt-controller/msi.txt When the iProc event queue based MSI is used, one needs to define the following properties in the MSI device node: @@ -80,9 +95,7 @@ Example: phy-names = "pcie-phy"; brcm,pcie-ob; - brcm,pcie-ob-oarr-size; brcm,pcie-ob-axi-offset = <0x00000000>; - brcm,pcie-ob-window-size = <256>; msi-parent = <&msi0>; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index 41e9f55a1467..ee1c72d5162e 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -15,6 +15,7 @@ Required properties: - compatible: should contain the platform identifier such as: "fsl,ls1021a-pcie", "snps,dw-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie" + "fsl,ls1046a-pcie" - reg: base addresses and lengths of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index b8cc395fffea..982a74ea6df9 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -110,6 +110,20 @@ Power supplies for Tegra124: - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must supply 1.05 V. +Power supplies for Tegra210: +- Required: + - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output + clocks. Must supply 1.8 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: @@ -436,3 +450,99 @@ Board DTS: status = "okay"; }; }; + +Tegra210: +--------- + +SoC DTSI: + + pcie-controller@01003000 { + compatible = "nvidia,tegra210-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA210_CLK_PCIE>, + <&tegra_car TEGRA210_CLK_AFI>, + <&tegra_car TEGRA210_CLK_PLL_E>, + <&tegra_car TEGRA210_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <4>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@01003000 { + status = "okay"; + + avdd-pll-uerefe-supply = <&avdd_1v05_pll>; + hvddio-pex-supply = <&vdd_1v8>; + dvddio-pex-supply = <&vdd_pex_1v05>; + dvdd-pex-pll-supply = <&vdd_pex_1v05>; + hvdd-pex-pll-e-supply = <&vdd_1v8>; + vddio-pex-ctl-supply = <&vdd_1v8>; + + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>; + phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3"; + status = "okay"; + }; + + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 08dcfad09f8d..50f9e2ca5b13 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -18,3 +18,9 @@ driver implementation may support the following properties: host bridges in the system, otherwise potentially conflicting domain numbers may be assigned to root buses behind different host bridges. The domain number for each host bridge in the system must be unique. +- max-link-speed: + If present this property specifies PCI gen for link capability. Host + drivers could add this as a strategy to avoid unnecessary operation for + unsupported link speed, for instance, trying to do training for + unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' + for gen2, and '1' for gen1. Any other values are invalid. diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 4059a6f89bc1..e15f9b19901f 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -7,6 +7,7 @@ - "qcom,pcie-ipq8064" for ipq8064 - "qcom,pcie-apq8064" for apq8064 - "qcom,pcie-apq8084" for apq8084 + - "qcom,pcie-msm8996" for msm8996 or apq8096 - reg: Usage: required @@ -92,6 +93,17 @@ - "aux" Auxiliary (AUX) clock - "bus_master" Master AXI clock - "bus_slave" Slave AXI clock + +- clock-names: + Usage: required for msm8996/apq8096 + Value type: <stringlist> + Definition: Should contain the following entries + - "pipe" Pipe Clock driving internal logic + - "aux" Auxiliary (AUX) clock + - "cfg" Configuration clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock + - resets: Usage: required Value type: <prop-encoded-array> @@ -115,7 +127,7 @@ - "core" Core reset - power-domains: - Usage: required for apq8084 + Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> Definition: A phandle and power domain specifier pair to the power domain which is responsible for collapsing diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 6cf99690eef9..eee518db90b9 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -7,6 +7,7 @@ compatible: "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7793" for the R8A7793 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index 66dcaa9efd74..e705acd3612c 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -7,6 +7,9 @@ Required properties: - reg : offset and length of the register set for the mux registers +- #pinctrl-cells : number of cells in addition to the index, set to 1 + for pinctrl-single,pins and 2 for pinctrl-single,bits + - pinctrl-single,register-width : pinmux register access width in bits - pinctrl-single,function-mask : mask of allowed pinmux function bits diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 0725fb37a973..d91715bc8d52 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -1,12 +1,14 @@ -DT bindings for the Renesas R-Car System Controller +DT bindings for the Renesas R-Car (RZ/G) System Controller == System Controller Node == -The R-Car System Controller provides power management for the CPU cores and -various coprocessors. +The R-Car (RZ/G) System Controller provides power management for the CPU cores +and various coprocessors. Required properties: - compatible: Must contain exactly one of the following: + - "renesas,r8a7743-sysc" (RZ/G1M) + - "renesas,r8a7745-sysc" (RZ/G1E) - "renesas,r8a7779-sysc" (R-Car H1) - "renesas,r8a7790-sysc" (R-Car H2) - "renesas,r8a7791-sysc" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt index 98d131acee95..a11072c5a866 100644 --- a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt +++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt @@ -2,11 +2,16 @@ TPS65217 Charger Required Properties: -compatible: "ti,tps65217-charger" +-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change. + Should be <0> for the USB charger and <1> for the AC adapter. +-interrupt-names: Should be "USB" and "AC" This node is a subnode of the tps65217 PMIC. Example: tps65217-charger { - compatible = "ti,tps65090-charger"; + compatible = "ti,tps65217-charger"; + interrupts = <0>, <1>; + interrupt-names = "USB", "AC"; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt index fb6fb31bc4c4..cf573e85b11d 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt @@ -3,7 +3,7 @@ BCM2835 PWM controller (Raspberry Pi controller) Required properties: - compatible: should be "brcm,bcm2835-pwm" - reg: physical base address and length of the controller's registers -- clock: This clock defines the base clock frequency of the PWM hardware +- clocks: This clock defines the base clock frequency of the PWM hardware system, the period and the duty_cycle of the PWM signal is a multiple of the base period. - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt new file mode 100644 index 000000000000..fa7849d67836 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt @@ -0,0 +1,21 @@ +Hisilicon PWM controller + +Required properties: +-compatible: should contain one SoC specific compatible string + The SoC specific strings supported including: + "hisilicon,hi3516cv300-pwm" + "hisilicon,hi3519v100-pwm" +- reg: physical base address and length of the controller's registers. +- clocks: phandle and clock specifier of the PWM reference clock. +- resets: phandle and reset specifier for the PWM controller reset. +- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of + the cells format. + +Example: + pwm: pwm@12130000 { + compatible = "hisilicon,hi3516cv300-pwm"; + reg = <0x12130000 0x10000>; + clocks = <&crg_ctrl HI3516CV300_PWM_CLK>; + resets = <&crg_ctrl 0x38 0>; + #pwm-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt index fccc1d24af58..02f0e9bbfbf8 100644 --- a/Documentation/devicetree/bindings/regulator/tps65218.txt +++ b/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -1,23 +1,78 @@ TPS65218 family of regulators Required properties: -For tps65218 regulators/LDOs -- compatible: - - "ti,tps65218-dcdc1" for DCDC1 - - "ti,tps65218-dcdc2" for DCDC2 - - "ti,tps65218-dcdc3" for DCDC3 - - "ti,tps65218-dcdc4" for DCDC4 - - "ti,tps65218-dcdc5" for DCDC5 - - "ti,tps65218-dcdc6" for DCDC6 - - "ti,tps65218-ldo1" for LDO1 - -Optional properties: -- Any optional property defined in bindings/regulator/regulator.txt +- compatible: "ti,tps65218" +- reg: I2C slave address + +- List of regulators provided by this controller, must be named + after their hardware counterparts: dcdc[1-6] and ldo1 +- This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at ./regulator.txt. + + The valid names for regulators are: + tps65217: regulator-dcdc1, regulator-dcdc2, regulator-dcdc3, regulator-dcdc4, + regulator-dcdc5, regulator-dcdc6, regulator-ldo1, regulator-ls3. + Each regulator is defined using the standard binding for regulators. Example: +tps65218: tps65218@24 { + reg = <0x24>; + compatible = "ti,tps65218"; + interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */ + interrupt-controller; + #interrupt-cells = <2>; + + dcdc1: regulator-dcdc1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1144000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc2: regulator-dcdc2 { + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1378000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3: regulator-dcdc3 { + regulator-name = "vdcdc3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc5: regulator-dcdc5 { + regulator-name = "v1_0bat"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc6: regulator-dcdc6 { + regulator-name = "v1_8bat"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: regulator-ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; - xyz: regulator@0 { - compatible = "ti,tps65218-dcdc1"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <3000000>; + ls3: regulator-ls3 { + regulator-min-microvolt = <100000>; + regulator-max-microvolt = <1000000>; }; +}; diff --git a/Documentation/devicetree/bindings/reset/oxnas,reset.txt b/Documentation/devicetree/bindings/reset/oxnas,reset.txt index 6f06db930030..d27ccb5d04fc 100644 --- a/Documentation/devicetree/bindings/reset/oxnas,reset.txt +++ b/Documentation/devicetree/bindings/reset/oxnas,reset.txt @@ -5,45 +5,19 @@ Please also refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "oxsemi,ox810se-reset" +- compatible: For OX810SE, should be "oxsemi,ox810se-reset" + For OX820, should be "oxsemi,ox820-reset" - #reset-cells: 1, see below Parent node should have the following properties : -- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" +- compatible: For OX810SE, should be : + "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + For OX820, should be : + "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd" -For OX810SE, the indices are : - - 0 : ARM - - 1 : COPRO - - 2 : Reserved - - 3 : Reserved - - 4 : USBHS - - 5 : USBHSPHY - - 6 : MAC - - 7 : PCI - - 8 : DMA - - 9 : DPE - - 10 : DDR - - 11 : SATA - - 12 : SATA_LINK - - 13 : SATA_PHY - - 14 : Reserved - - 15 : NAND - - 16 : GPIO - - 17 : UART1 - - 18 : UART2 - - 19 : MISC - - 20 : I2S - - 21 : AHB_MON - - 22 : UART3 - - 23 : UART4 - - 24 : SGDMA - - 25 : Reserved - - 26 : Reserved - - 27 : Reserved - - 28 : Reserved - - 29 : Reserved - - 30 : Reserved - - 31 : BUS +Reset indices are in dt-bindings include files : +- For OX810SE: include/dt-bindings/reset/oxsemi,ox810se.h +- For OX820: include/dt-bindings/reset/oxsemi,ox820.h example: diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt index 1cfd21d1dfa1..92527138bc93 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt @@ -16,15 +16,14 @@ Please refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "st,<chip>-powerdown" - ex: "st,stih415-powerdown", "st,stih416-powerdown" +- compatible: Should be "st,stih407-powerdown" - #reset-cells: 1, see below example: powerdown: powerdown-controller { + compatible = "st,stih407-powerdown"; #reset-cells = <1>; - compatible = "st,stih415-powerdown"; }; @@ -37,11 +36,10 @@ index specifying which channel to use, as described in reset.txt example: - usb1: usb@fe200000 { - resets = <&powerdown STIH41X_USB1_POWERDOWN>; + st_dwc3: dwc3@8f94000 { + resets = <&powerdown STIH407_USB3_POWERDOWN>, }; Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset/stih415-resets.h -include/dt-bindings/reset/stih416-resets.h +include/dt-bindings/reset/stih407-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt index 891a2fd85ed6..a21658f18fe6 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -15,15 +15,14 @@ Please refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "st,<chip>-softreset" example: - "st,stih415-softreset" or "st,stih416-softreset"; +- compatible: Should be st,stih407-softreset"; - #reset-cells: 1, see below example: softreset: softreset-controller { #reset-cells = <1>; - compatible = "st,stih415-softreset"; + compatible = "st,stih407-softreset"; }; @@ -42,5 +41,4 @@ example: Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset/stih415-resets.h -include/dt-bindings/reset/stih416-resets.h +include/dt-bindings/reset/stih407-resets.h diff --git a/Documentation/devicetree/bindings/rng/omap_rng.txt b/Documentation/devicetree/bindings/rng/omap_rng.txt index 6a62acd86953..471477299ece 100644 --- a/Documentation/devicetree/bindings/rng/omap_rng.txt +++ b/Documentation/devicetree/bindings/rng/omap_rng.txt @@ -1,4 +1,4 @@ -OMAP SoC HWRNG Module +OMAP SoC and Inside-Secure HWRNG Module Required properties: @@ -6,11 +6,13 @@ Required properties: RNG versions: - "ti,omap2-rng" for OMAP2. - "ti,omap4-rng" for OMAP4, OMAP5 and AM33XX. + - "inside-secure,safexcel-eip76" for SoCs with EIP76 IP block Note that these two versions are incompatible. - ti,hwmods: Name of the hwmod associated with the RNG module - reg : Offset and length of the register set for the module - interrupts : the interrupt number for the RNG module. - Only used for "ti,omap4-rng". + Used for "ti,omap4-rng" and "inside-secure,safexcel-eip76" +- clocks: the trng clock source Example: /* AM335x */ @@ -20,3 +22,11 @@ rng: rng@48310000 { reg = <0x48310000 0x2000>; interrupts = <111>; }; + +/* SafeXcel IP-76 */ +trng: rng@f2760000 { + compatible = "inside-secure,safexcel-eip76"; + reg = <0xf2760000 0x7d>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpm_syscon0 1 25>; +}; diff --git a/Documentation/devicetree/bindings/rtc/epson,rtc7301.txt b/Documentation/devicetree/bindings/rtc/epson,rtc7301.txt new file mode 100644 index 000000000000..5f9df3f1467c --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/epson,rtc7301.txt @@ -0,0 +1,16 @@ +EPSON TOYOCOM RTC-7301SF/DG + +Required properties: + +- compatible: Should be "epson,rtc7301sf" or "epson,rtc7301dg" +- reg: Specifies base physical address and size of the registers. +- interrupts: A single interrupt specifier. + +Example: + +rtc: rtc@44a00000 { + compatible = "epson,rtc7301dg"; + reg = <0x44a00000 0x10000>; + interrupt-parent = <&axi_intc_0>; + interrupts = <3 2>; +}; diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt new file mode 100644 index 000000000000..41c7ae18fd7b --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt @@ -0,0 +1,37 @@ +JZ4740 and similar SoCs real-time clock driver + +Required properties: + +- compatible: One of: + - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC + - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC +- reg: Address range of rtc register set +- interrupts: IRQ number for the alarm interrupt +- clocks: phandle to the "rtc" clock +- clock-names: must be "rtc" + +Optional properties: +- system-power-controller: To use this component as the + system power controller +- reset-pin-assert-time-ms: Reset pin low-level assertion + time after wakeup (default 60ms; range 0-125ms if RTC clock + at 32 kHz) +- min-wakeup-pin-assert-time-ms: Minimum wakeup pin assertion + time (default 100ms; range 0-2s if RTC clock at 32 kHz) + +Example: + +rtc@10003000 { + compatible = "ingenic,jz4740-rtc"; + reg = <0x10003000 0x40>; + + interrupt-parent = <&intc>; + interrupts = <32>; + + clocks = <&rtc_clock>; + clock-names = "rtc"; + + system-power-controller; + reset-pin-assert-time-ms = <60>; + min-wakeup-pin-assert-time-ms = <100>; +}; diff --git a/Documentation/devicetree/bindings/rtc/twl-rtc.txt b/Documentation/devicetree/bindings/rtc/twl-rtc.txt index 596e0c97be7a..8f9a94f2f896 100644 --- a/Documentation/devicetree/bindings/rtc/twl-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/twl-rtc.txt @@ -1,12 +1,11 @@ -* TI twl RTC - -The TWL family (twl4030/6030) contains a RTC. +* Texas Instruments TWL4030/6030 RTC Required properties: -- compatible : Should be twl4030-rtc - -Examples: - -rtc@0 { - compatible = "ti,twl4030-rtc"; -}; +- compatible : Should be "ti,twl4030-rtc" +- interrupts : Should be the interrupt number. + +Example: + rtc { + compatible = "ti,twl4030-rtc"; + interrupts = <11>; + }; diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index bf2411f366e5..2a42a323fa1a 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -6,6 +6,7 @@ Main node required properties: - compatible : value should be as follows: (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset + (c) "hisilicon,hip07-sas-v2" for v2 hw in hip07 chipset - sas-addr : array of 8 bytes for host SAS address - reg : Address and length of the SAS register - hisilicon,sas-syscon: phandle of syscon used for sas control diff --git a/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt b/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt new file mode 100644 index 000000000000..d89f99971368 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/ibmvtpm.txt @@ -0,0 +1,41 @@ +* Device Tree Bindings for IBM Virtual Trusted Platform Module(vtpm) + +Required properties: + +- compatible : property name that conveys the platform architecture + identifiers, as 'IBM,vtpm' +- device_type : specifies type of virtual device +- interrupts : property specifying the interrupt source number and + sense code associated with this virtual I/O Adapters +- ibm,my-drc-index : integer index for the connector between the device + and its parent - present only if Dynamic + Reconfiguration(DR) Connector is enabled +- ibm,#dma-address-cells: specifies the number of cells that are used to + encode the physical address field of dma-window + properties +- ibm,#dma-size-cells : specifies the number of cells that are used to + encode the size field of dma-window properties +- ibm,my-dma-window : specifies DMA window associated with this virtual + IOA +- ibm,loc-code : specifies the unique and persistent location code + associated with this virtual I/O Adapters +- linux,sml-base : 64-bit base address of the reserved memory allocated + for the firmware event log +- linux,sml-size : size of the memory allocated for the firmware event log + +Example (IBM Virtual Trusted Platform Module) +--------------------------------------------- + + vtpm@30000003 { + ibm,#dma-size-cells = <0x2>; + compatible = "IBM,vtpm"; + device_type = "IBM,vtpm"; + ibm,my-drc-index = <0x30000003>; + ibm,#dma-address-cells = <0x2>; + linux,sml-base = <0xc60e 0x0>; + interrupts = <0xa0003 0x0>; + ibm,my-dma-window = <0x10000003 0x0 0x0 0x0 0x10000000>; + ibm,loc-code = "U8286.41A.10082DV-V3-C3"; + reg = <0x30000003>; + linux,sml-size = <0xbce10200>; + }; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt new file mode 100644 index 000000000000..8cb638b7e89c --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm-i2c.txt @@ -0,0 +1,21 @@ +* Device Tree Bindings for I2C based Trusted Platform Module(TPM) + +Required properties: + +- compatible : 'manufacturer,model', eg. nuvoton,npct650 +- label : human readable string describing the device, eg. "tpm" +- linux,sml-base : 64-bit base address of the reserved memory allocated for + the firmware event log +- linux,sml-size : size of the memory allocated for the firmware event log + +Example (for OpenPower Systems with Nuvoton TPM 2.0 on I2C) +---------------------------------------------------------- + +tpm@57 { + reg = <0x57>; + label = "tpm"; + compatible = "nuvoton,npct650", "nuvoton,npct601"; + linux,sml-base = <0x7f 0xfd450000>; + linux,sml-size = <0x10000>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt new file mode 100644 index 000000000000..41d740545189 --- /dev/null +++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_mmio.txt @@ -0,0 +1,25 @@ +Trusted Computing Group MMIO Trusted Platform Module + +The TCG defines multi vendor standard for accessing a TPM chip, this +is the standard protocol defined to access the TPM via MMIO. Typically +this interface will be implemented over Intel's LPC bus. + +Refer to the 'TCG PC Client Specific TPM Interface Specification (TIS)' TCG +publication for the specification. + +Required properties: + +- compatible: should contain a string below for the chip, followed by + "tcg,tpm-tis-mmio". Valid chip strings are: + * "atmel,at97sc3204" +- reg: The location of the MMIO registers, should be at least 0x5000 bytes +- interrupt-parent/interrupts: An optional interrupt indicating command completion. + +Example: + + tpm_tis@90000 { + compatible = "atmel,at97sc3204", "tcg,tpm-tis-mmio"; + reg = <0x90000 0x5000>; + interrupt-parent = <&EIC0>; + interrupts = <1 2>; + }; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt index 845850caf088..c93a2d1c1a65 100644 --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt @@ -10,7 +10,7 @@ Required properties: See ../reset/reset.txt for details. - reset-names : Must include the following entries: - serial -- dmas : Must contain an entry for each entry in clock-names. +- dmas : Must contain an entry for each entry in dma-names. See ../dma/dma.txt for details. - dma-names : Must include the following entries: - rx diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index e8f15e34027f..16fe94d7783c 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -9,17 +9,20 @@ domain control. The driver implements the Generic PM domain bindings described in power/power_domain.txt. It provides the power domains defined in -include/dt-bindings/power/mt8173-power.h. +include/dt-bindings/power/mt8173-power.h and mt2701-power.h. Required properties: -- compatible: Must be "mediatek,mt8173-scpsys" +- compatible: Should be one of: + - "mediatek,mt2701-scpsys" + - "mediatek,mt8173-scpsys" - #power-domain-cells: Must be 1 - reg: Address range of the SCPSYS unit - infracfg: must contain a phandle to the infracfg controller - clock, clock-names: clocks according to the common clock binding. - The clocks needed "mm", "mfg", "venc" and "venc_lt". - These are the clocks which hardware needs to be enabled - before enabling certain power domains. + These are clocks which hardware needs to be + enabled before enabling certain power domains. + Required clocks for MT2701: "mm", "mfg", "ethif" + Required clocks for MT8173: "mm", "mfg", "venc", "venc_lt" Optional properties: - vdec-supply: Power supply for the vdec power domain diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt new file mode 100644 index 000000000000..5b9b38f578bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt @@ -0,0 +1,88 @@ +Devicetree bindings for the Axentia TSE-850 audio complex + +Required properties: + - compatible: "axentia,tse850-pcm5142" + - axentia,ssc-controller: The phandle of the atmel SSC controller used as + cpu dai. + - axentia,audio-codec: The phandle of the PCM5142 codec. + - axentia,add-gpios: gpio specifier that controls the mixer. + - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1. + - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2. + - axentia,ana-supply: Regulator that supplies the output amplifier. Must + support voltages in the 2V - 20V range, in 1V steps. + +The schematics explaining the gpios are as follows: + + loop1 relays + IN1 +---o +------------+ o---+ OUT1 + \ / + + + + | / | + +--o +--. | + | add | | + | V | + | .---. | + DAC +----------->|Sum|---+ + | '---' | + | | + + + + + IN2 +---o--+------------+--o---+ OUT2 + loop2 relays + +The 'loop1' gpio pin controlls two relays, which are either in loop position, +meaning that input and output are directly connected, or they are in mixer +position, meaning that the signal is passed through the 'Sum' mixer. Similarly +for 'loop2'. + +In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer +(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays +are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2 +are TSE-850 connectors and DAC is the PCB name of the (filtered) output from +the PCM5142 codec. + +Example: + + &i2c { + codec: pcm5142@4c { + compatible = "ti,pcm5142"; + + reg = <0x4c>; + + AVDD-supply = <®_3v3>; + DVDD-supply = <®_3v3>; + CPVDD-supply = <®_3v3>; + + clocks = <&sck>; + + pll-in = <3>; + pll-out = <6>; + }; + }; + + ana: ana-reg { + compatible = "pwm-regulator"; + + regulator-name = "ANA"; + + pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>; + pwm-dutycycle-unit = <1000>; + pwm-dutycycle-range = <100 1000>; + + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <20000000>; + regulator-ramp-delay = <1000>; + }; + + sound { + compatible = "axentia,tse850-pcm5142"; + + axentia,ssc-controller = <&ssc0>; + axentia,audio-codec = <&codec>; + + axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>; + axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>; + axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>; + + axentia,ana-supply = <&ana>; + }; diff --git a/Documentation/devicetree/bindings/sound/cs35l34.txt b/Documentation/devicetree/bindings/sound/cs35l34.txt new file mode 100644 index 000000000000..b218ead2e68e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l34.txt @@ -0,0 +1,64 @@ +CS35L34 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l34" + + - reg : the I2C address of the device for I2C. + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + + - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost + converter's output voltage in mV. The range is from VP to 8V with + increments of 100mV. + + - cirrus,boost-nanohenry: Inductor value for boost converter. The value is + in nH and they can be values of 1000nH, 1100nH, 1200nH, 1500nH, and 2200nH. + +Optional properties: + + - reset-gpios: GPIO used to reset the amplifier. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS35L34 are delivered to. + - interrupts : IRQ line info CS35L34. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The + range starts at 1200mA and goes to a maximum of 3840mA with increments of + 80mA. The default value is 2480mA. + + - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the + received mono data is in the left or right portion of the I2S frame + according to the AD0 pin or directly via this configuration. + 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel), + 0x2 = Left, + 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right + channel), + 0x3 = Right. + + - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take + effect without waiting for a zero cross. + + - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of + SCLK. Otherwise, data is on the falling edge of SCLK. + + +Example: + +cs35l34: cs35l34@40 { + compatible = "cirrus,cs35l34"; + reg = <0x40>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&gpio 10 0>; + + cirrus,boost-vtge-milltvolt = <8000>; /* 8V */ + cirrus,boost-ind-nanohenry = <1000>; /* 1uH */ + cirrus,boost-peak-milliamp = <3000>; /* 3A */ +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l42.txt b/Documentation/devicetree/bindings/sound/cs42l42.txt new file mode 100644 index 000000000000..9a2c5e2423d5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l42.txt @@ -0,0 +1,110 @@ +CS42L42 audio CODEC + +Required properties: + + - compatible : "cirrus,cs42l42" + + - reg : the I2C address of the device for I2C. + + - VP-supply, VCP-supply, VD_FILT-supply, VL-supply, VA-supply : + power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - interrupt-parent : Specifies the phandle of the interrupt controller to + which the IRQs from CS42L42 are delivered to. + + - interrupts : IRQ line info CS42L42. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,ts-inv : Boolean property. For jacks that invert the tip sense + polarity. Normal jacks will short tip sense pin to HS1 when headphones are + plugged in and leave tip sense floating when not plugged in. Inverting jacks + short tip sense when unplugged and float when plugged in. + + 0 = (Default) Non-inverted + 1 = Inverted + + - cirrus,ts-dbnc-rise : Debounce the rising edge of TIP_SENSE_PLUG. With no + debounce, the tip sense pin might be noisy on a plug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,ts-dbnc-fall : Debounce the falling edge of TIP_SENSE_UNPLUG. + With no debounce, the tip sense pin might be noisy on an unplug event. + + 0 - 0ms, + 1 - 125ms, + 2 - 250ms, + 3 - 500ms, + 4 - 750ms, + 5 - (Default) 1s, + 6 - 1.25s, + 7 - 1.5s, + + - cirrus,btn-det-init-dbnce : This sets how long the driver sleeps after + enabling button detection interrupts. After auto-detection and before + servicing button interrupts, the HS bias needs time to settle. If you + don't wait, there is possibility for erroneous button interrupt. + + 0ms - 200ms, + Default = 100ms + + - cirrus,btn-det-event-dbnce : This sets how long the driver delays after + receiving a button press interrupt. With level detect interrupts, you want + to wait a small amount of time to make sure the button press is making a + clean connection with the bias resistors. + + 0ms - 20ms, + Default = 10ms + + - cirrus,bias-lvls : For a level-detect headset button scheme, each button + will bias the mic pin to a certain voltage. To determine which button was + pressed, the driver will compare this biased voltage to sequential, + decreasing voltages and will stop when a comparator is tripped, + indicating a comparator voltage < bias voltage. This value represents a + percentage of the internally generated HS bias voltage. For different + hardware setups, a designer might want to tweak this. This is an array of + descending values for the comparator voltage. + + Array of 4 values + Each 0-63 + < x1 x2 x3 x4 > + Default = < 15 8 4 1> + + +Example: + +cs42l42: cs42l42@48 { + compatible = "cirrus,cs42l42"; + reg = <0x48>; + VA-supply = <&dummy_vreg>; + VP-supply = <&dummy_vreg>; + VCP-supply = <&dummy_vreg>; + VD_FILT-supply = <&dummy_vreg>; + VL-supply = <&dummy_vreg>; + + reset-gpios = <&axi_gpio_0 1 0>; + interrupt-parent = <&gpio0>; + interrupts = <55 8> + + cirrus,ts-inv = <0x00>; + cirrus,ts-dbnc-rise = <0x05>; + cirrus,ts-dbnc-fall = <0x00>; + cirrus,btn-det-init-dbnce = <100>; + cirrus,btn-det-event-dbnce = <10>; + cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; + cirrus,hs-bias-ramp-rate = <0x02>; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt index 55b53e1fd72c..e0b6165c9cfc 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcbsp.txt @@ -43,7 +43,7 @@ mcbsp0: mcbsp@1d10000 { <0x00310000 0x1000>; reg-names = "mpu", "dat"; interrupts = <97 98>; - interrupts-names = "rx", "tx"; + interrupt-names = "rx", "tx"; dmas = <&edma0 3 1 &edma0 2 1>; dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt index d9d8635ff94c..6a4aadc4ce06 100644 --- a/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt +++ b/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt @@ -44,8 +44,7 @@ Required dai-link subnodes: Required CPU/CODEC subnodes properties: -link-name : Name of the dai link. --sound-dai : phandle and port of CPU/CODEC --capture-dai : phandle and port of CPU/CODEC +-sound-dai : phandle/s and port of CPU/CODEC Example: @@ -73,7 +72,7 @@ sound: sound { sound-dai = <&lpass MI2S_PRIMARY>; }; codec { - sound-dai = <&wcd_codec 0>; + sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt new file mode 100644 index 000000000000..ccb401cfef9d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -0,0 +1,85 @@ +msm8916 analog audio CODEC + +Bindings for codec Analog IP which is integrated in pmic pm8916, + +## Bindings for codec core on pmic: + +Required properties + - compatible = "qcom,pm8916-wcd-analog-codec"; + - reg: represents the slave base address provided to the peripheral. + - interrupt-parent : The parent interrupt controller. + - interrupts: List of interrupts in given SPMI peripheral. + - interrupt-names: Names specified to above list of interrupts in same + order. List of supported interrupt names are: + "cdc_spk_cnp_int" - Speaker click and pop interrupt. + "cdc_spk_clip_int" - Speaker clip interrupt. + "cdc_spk_ocp_int" - Speaker over current protect interrupt. + "mbhc_ins_rem_det1" - jack insert removal detect interrupt 1. + "mbhc_but_rel_det" - button release interrupt. + "mbhc_but_press_det" - button press event + "mbhc_ins_rem_det" - jack insert removal detect interrupt. + "mbhc_switch_int" - multi button headset interrupt. + "cdc_ear_ocp_int" - Earphone over current protect interrupt. + "cdc_hphr_ocp_int" - Headphone R over current protect interrupt. + "cdc_hphl_ocp_det" - Headphone L over current protect interrupt. + "cdc_ear_cnp_int" - earphone cnp interrupt. + "cdc_hphr_cnp_int" - hphr click and pop interrupt. + "cdc_hphl_cnp_int" - hphl click and pop interrupt. + + - clocks: Handle to mclk. + - clock-names: should be "mclk" + - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. + - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. + - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. + +Optional Properties: +- qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor + connected. +- qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor + connected. + +Example: + +spmi_bus { + ... + audio-codec@f000{ + compatible = "qcom,pm8916-wcd-analog-codec"; + reg = <0xf000 0x200>; + reg-names = "pmic-codec-core"; + clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "mclk"; + interrupt-parent = <&spmi_bus>; + interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, + <0x1 0xf0 0x1 IRQ_TYPE_NONE>, + <0x1 0xf0 0x2 IRQ_TYPE_NONE>, + <0x1 0xf0 0x3 IRQ_TYPE_NONE>, + <0x1 0xf0 0x4 IRQ_TYPE_NONE>, + <0x1 0xf0 0x5 IRQ_TYPE_NONE>, + <0x1 0xf0 0x6 IRQ_TYPE_NONE>, + <0x1 0xf0 0x7 IRQ_TYPE_NONE>, + <0x1 0xf1 0x0 IRQ_TYPE_NONE>, + <0x1 0xf1 0x1 IRQ_TYPE_NONE>, + <0x1 0xf1 0x2 IRQ_TYPE_NONE>, + <0x1 0xf1 0x3 IRQ_TYPE_NONE>, + <0x1 0xf1 0x4 IRQ_TYPE_NONE>, + <0x1 0xf1 0x5 IRQ_TYPE_NONE>; + interrupt-names = "cdc_spk_cnp_int", + "cdc_spk_clip_int", + "cdc_spk_ocp_int", + "mbhc_ins_rem_det1", + "mbhc_but_rel_det", + "mbhc_but_press_det", + "mbhc_ins_rem_det", + "mbhc_switch_int", + "cdc_ear_ocp_int", + "cdc_hphr_ocp_int", + "cdc_hphl_ocp_det", + "cdc_ear_cnp_int", + "cdc_hphr_cnp_int", + "cdc_hphl_cnp_int"; + VDD-CDC-IO-supply = <&pm8916_l5>; + VDD-CDC-TX-RX-CX-supply = <&pm8916_l5>; + VDD-MICBIAS-supply = <&pm8916_l13>; + #sound-dai-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt new file mode 100644 index 000000000000..1c8e4cb25176 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-digital.txt @@ -0,0 +1,20 @@ +msm8916 digital audio CODEC + +## Bindings for codec core in lpass: + +Required properties + - compatible = "qcom,msm8916-wcd-digital-codec"; + - reg: address space for lpass codec. + - clocks: Handle to mclk and ahbclk + - clock-names: should be "mclk", "ahbix-clk". + +Example: + +audio-codec@771c000{ + compatible = "qcom,msm8916-wcd-digital-codec"; + reg = <0x0771c000 0x400>; + clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>, + <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "ahbix-clk", "mclk"; + #sound-dai-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5514.txt b/Documentation/devicetree/bindings/sound/rt5514.txt index 9cabfc18cb57..929ca6756b02 100644 --- a/Documentation/devicetree/bindings/sound/rt5514.txt +++ b/Documentation/devicetree/bindings/sound/rt5514.txt @@ -13,6 +13,9 @@ Optional properties: - clocks: The phandle of the master clock to the CODEC - clock-names: Should be "mclk" +- realtek,dmic-init-delay-ms + Set the DMIC initial delay (ms) to wait it ready. + Pins on the device (for linking into audio routes) for RT5514: * DMIC1L diff --git a/Documentation/devicetree/bindings/sound/rt5663.txt b/Documentation/devicetree/bindings/sound/rt5663.txt index 7d3c974c6e2e..70eaeaed2b18 100644 --- a/Documentation/devicetree/bindings/sound/rt5663.txt +++ b/Documentation/devicetree/bindings/sound/rt5663.txt @@ -1,10 +1,10 @@ -RT5663/RT5668 audio CODEC +RT5663 audio CODEC This device supports I2C only. Required properties: -- compatible : One of "realtek,rt5663" or "realtek,rt5668". +- compatible : "realtek,rt5663". - reg : The I2C address of the device. @@ -12,7 +12,7 @@ Required properties: Optional properties: -Pins on the device (for linking into audio routes) for RT5663/RT5668: +Pins on the device (for linking into audio routes) for RT5663: * IN1P * IN1N diff --git a/Documentation/devicetree/bindings/sound/rt5665.txt b/Documentation/devicetree/bindings/sound/rt5665.txt new file mode 100755 index 000000000000..419c89219681 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5665.txt @@ -0,0 +1,68 @@ +RT5665/RT5666/RT5668 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : One of "realtek,rt5665", "realtek,rt5666" or "realtek,rt5668". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential +- realtek,in3-differential +- realtek,in4-differential + Boolean. Indicate MIC1/2/3/4 input are differential, rather than single-ended. + +- realtek,dmic1-data-pin + 0: dmic1 is not used + 1: using GPIO4 pin as dmic1 data pin + 2: using IN2N pin as dmic2 data pin + +- realtek,dmic2-data-pin + 0: dmic2 is not used + 1: using GPIO5 pin as dmic2 data pin + 2: using IN2P pin as dmic2 data pin + +- realtek,jd-src + 0: No JD is used + 1: using JD1 as JD source + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Pins on the device (for linking into audio routes) for RT5659/RT5658: + + * DMIC L1 + * DMIC R1 + * DMIC L2 + * DMIC R2 + * IN1P + * IN1N + * IN2P + * IN2N + * IN3P + * IN3N + * IN4P + * IN4N + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOOUT + * PDML + * PDMR + +Example: + +rt5659 { + compatible = "realtek,rt5665"; + reg = <0x1b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt new file mode 100644 index 000000000000..94442e5673b3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,tm2-audio.txt @@ -0,0 +1,38 @@ +Samsung Exynos5433 TM2(E) audio complex with WM5110 codec + +Required properties: + + - compatible : "samsung,tm2-audio" + - model : the user-visible name of this sound complex + - audio-codec : the phandle of the wm5110 audio codec node, + as described in ../mfd/arizona.txt + - i2s-controller : the phandle of the I2S controller + - audio-amplifier : the phandle of the MAX98504 amplifier + - samsung,audio-routing : a list of the connections between audio components; + each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source; valid names for sources and sinks are the + WM5110's and MAX98504's pins and the jacks on the + board: HP, SPK, Main Mic, Sub Mic, Third Mic, + Headset Mic + - mic-bias-gpios : GPIO pin that enables the Main Mic bias regulator + + +Example: + +sound { + compatible = "samsung,tm2-audio"; + audio-codec = <&wm5110>; + i2s-controller = <&i2s0>; + audio-amplifier = <&max98504>; + mic-bias-gpios = <&gpr3 2 0>; + model = "wm5110"; + samsung,audio-routing = + "HP", "HPOUT1L", + "HP", "HPOUT1R", + "SPK", "SPKOUT", + "SPKOUT", "HPOUT2L", + "SPKOUT", "HPOUT2R", + "Main Mic", "MICBIAS2", + "IN1R", "Main Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt index 0dce690f78f5..3033bd8aab0f 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt @@ -1,8 +1,12 @@ * Allwinner A10 Codec Required properties: -- compatible: must be either "allwinner,sun4i-a10-codec" or - "allwinner,sun7i-a20-codec" +- compatible: must be one of the following compatibles: + - "allwinner,sun4i-a10-codec" + - "allwinner,sun6i-a31-codec" + - "allwinner,sun7i-a20-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" - reg: must contain the registers location and length - interrupts: must contain the codec interrupt - dmas: DMA channels for tx and rx dma. See the DMA client binding, @@ -17,6 +21,43 @@ Required properties: Optional properties: - allwinner,pa-gpios: gpio to enable external amplifier +Required properties for the following compatibles: + - "allwinner,sun6i-a31-codec" + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- resets: phandle to the reset control for this device +- allwinner,audio-routing: A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names include: + + Audio pins on the SoC: + "HP" + "HPCOM" + "LINEIN" + "LINEOUT" (not on sun8i-a23) + "MIC1" + "MIC2" + "MIC3" (sun6i-a31 only) + + Microphone biases from the SoC: + "HBIAS" + "MBIAS" + + Board connectors: + "Headphone" + "Headset Mic" + "Line In" + "Line Out" + "Mic" + "Speaker" + +Required properties for the following compatibles: + - "allwinner,sun8i-a23-codec" + - "allwinner,sun8i-h3-codec" +- allwinner,codec-analog-controls: A phandle to the codec analog controls + block in the PRCM. + Example: codec: codec@01c22c00 { #sound-dai-cells = <0>; @@ -28,3 +69,23 @@ codec: codec@01c22c00 { dmas = <&dma 0 19>, <&dma 0 19>; dma-names = "rx", "tx"; }; + +codec: codec@01c22c00 { + #sound-dai-cells = <0>; + compatible = "allwinner,sun6i-a31-codec"; + reg = <0x01c22c00 0x98>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_APB1_CODEC>, <&ccu CLK_CODEC>; + clock-names = "apb", "codec"; + resets = <&ccu RST_APB1_CODEC>; + dmas = <&dma 15>, <&dma 15>; + dma-names = "rx", "tx"; + allwinner,audio-routing = + "Headphone", "HP", + "Speaker", "LINEOUT", + "LINEIN", "Line In", + "MIC1", "MBIAS", + "MIC1", "Mic", + "MIC2", "HBIAS", + "MIC2", "Headset Mic"; +}; diff --git a/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt new file mode 100644 index 000000000000..779b735781ba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt @@ -0,0 +1,16 @@ +* Allwinner Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun8i-a23-codec-analog" + - "allwinner,sun8i-h3-codec-analog" + +Required properties if not a sub-node of the PRCM node: +- reg: must contain the registers location and length + +Example: +prcm: prcm@01f01400 { + codec_analog: codec-analog { + compatible = "allwinner,sun8i-a23-codec-analog"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt index 9340d2ddcc54..6fbba562eaa7 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt @@ -12,6 +12,7 @@ Required properties: "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP) "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP) "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP) + "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP) - reg - <int> - I2C slave address - HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply, diff --git a/Documentation/devicetree/bindings/sound/wm8580.txt b/Documentation/devicetree/bindings/sound/wm8580.txt index 7d9821f348da..78fce9b14954 100644 --- a/Documentation/devicetree/bindings/sound/wm8580.txt +++ b/Documentation/devicetree/bindings/sound/wm8580.txt @@ -1,10 +1,10 @@ -WM8580 audio CODEC +WM8580 and WM8581 audio CODEC This device supports I2C only. Required properties: - - compatible : "wlf,wm8580" + - compatible : "wlf,wm8580", "wlf,wm8581" - reg : the I2C address of the device. diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index da6614c63796..dc975064fa27 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -1,17 +1,23 @@ Renesas MSIOF spi controller Required properties: -- compatible : "renesas,msiof-<soctype>" for SoCs, - "renesas,sh-msiof" for SuperH, or - "renesas,sh-mobile-msiof" for SH Mobile series. - Examples with soctypes are: - "renesas,msiof-r8a7790" (R-Car H2) +- compatible : "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) "renesas,msiof-r8a7794" (R-Car E2) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-sh73a0" (SH-Mobile AG5) + "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) + "renesas,rcar-gen2-msiof" (generic R-Car Gen2 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,sh-msiof" (deprecated) + + When compatible with the generic version, nodes + must list the SoC-specific version corresponding + to the platform first followed by the generic + version. + - reg : A list of offsets and lengths of the register sets for the device. If only one register set is present, it is to be used @@ -61,7 +67,8 @@ Documentation/devicetree/bindings/pinctrl/renesas,*. Example: msiof0: spi@e6e20000 { - compatible = "renesas,msiof-r8a7791"; + compatible = "renesas,msiof-r8a7791", + "renesas,rcar-gen2-msiof"; reg = <0 0xe6e20000 0 0x0064>; interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; diff --git a/Documentation/devicetree/bindings/sram/sram.txt b/Documentation/devicetree/bindings/sram/sram.txt index add48f09015e..068c2c03c38f 100644 --- a/Documentation/devicetree/bindings/sram/sram.txt +++ b/Documentation/devicetree/bindings/sram/sram.txt @@ -4,7 +4,7 @@ Simple IO memory regions to be managed by the genalloc API. Required properties: -- compatible : mmio-sram +- compatible : mmio-sram or atmel,sama5d2-securam - reg : SRAM iomem address range diff --git a/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt new file mode 100644 index 000000000000..474531d2b2c5 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt @@ -0,0 +1,17 @@ +Binding for Thermal Sensor driver for BCM2835 SoCs. + +Required parameters: +------------------- + +compatible: should be one of: "brcm,bcm2835-thermal", + "brcm,bcm2836-thermal" or "brcm,bcm2837-thermal" +reg: Address range of the thermal registers. +clocks: Phandle of the clock used by the thermal sensor. + +Example: + +thermal: thermal@7e212000 { + compatible = "brcm,bcm2835-thermal"; + reg = <0x7e212000 0x8>; + clocks = <&clocks BCM2835_CLOCK_TSENS>; +}; diff --git a/Documentation/devicetree/bindings/thermal/st-thermal.txt b/Documentation/devicetree/bindings/thermal/st-thermal.txt index 3b9251b4a145..a2f939137e35 100644 --- a/Documentation/devicetree/bindings/thermal/st-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/st-thermal.txt @@ -3,17 +3,8 @@ Binding for Thermal Sensor driver for STMicroelectronics STi series of SoCs. Required parameters: ------------------- -compatible : st,<SoC>-<module>-thermal; should be one of: - "st,stih415-sas-thermal", - "st,stih415-mpe-thermal", - "st,stih416-sas-thermal" - "st,stih416-mpe-thermal" - "st,stid127-thermal" or - "st,stih407-thermal" - according to the SoC type (stih415, stih416, stid127, stih407) - and module type (sas or mpe). On stid127 & stih407 there is only - one die/module, so there is no module type in the compatible - string. +compatible : Should be "st,stih407-thermal" + clock-names : Should be "thermal". See: Documentation/devicetree/bindings/resource-names.txt clocks : Phandle of the clock used by the thermal sensor. @@ -25,18 +16,17 @@ Optional parameters: reg : For non-sysconf based sensors, this should be the physical base address and length of the sensor's registers. interrupts : Standard way to define interrupt number. - Interrupt is mandatory to be defined when compatible is - "stih416-mpe-thermal". NB: For thermal sensor's for which no interrupt has been defined, a polling delay of 1000ms will be used to read the temperature from device. Example: - temp1@fdfe8000 { - compatible = "st,stih416-mpe-thermal"; - reg = <0xfdfe8000 0x10>; - clock-names = "thermal"; - clocks = <&clk_m_mpethsens>; - interrupts = <GIC_SPI 23 IRQ_TYPE_NONE>; + temp0@91a0000 { + compatible = "st,stih407-thermal"; + reg = <0x91a0000 0x28>; + clock-names = "thermal"; + clocks = <&CLK_SYSIN>; + interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>; + st,passive_cooling_temp = <110>; }; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt new file mode 100644 index 000000000000..e3cfce8fecc5 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt @@ -0,0 +1,17 @@ +NPS Network Processor + +Required properties: + +- compatible : should be "ezchip,nps400-timer0" + +Clocks required for compatible = "ezchip,nps400-timer0": +- interrupts : The interrupt of the first timer +- clocks : Must contain a single entry describing the clock input + +Example: + +timer { + compatible = "ezchip,nps400-timer0"; + interrupts = <3>; + clocks = <&sysclk>; +}; diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt index c8c03d700382..c0ab4190b8fb 100644 --- a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt @@ -2,14 +2,14 @@ NPS Network Processor Required properties: -- compatible : should be "ezchip,nps400-timer" +- compatible : should be "ezchip,nps400-timer1" -Clocks required for compatible = "ezchip,nps400-timer": +Clocks required for compatible = "ezchip,nps400-timer1": - clocks : Must contain a single entry describing the clock input Example: timer { - compatible = "ezchip,nps400-timer"; + compatible = "ezchip,nps400-timer1"; clocks = <&sysclk>; }; diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt index 070baf4d7d97..b6b5130e5f65 100644 --- a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt +++ b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt @@ -7,8 +7,11 @@ To bind UFS PHY with UFS host controller, the controller node should contain a phandle reference to UFS PHY node. Required properties: -- compatible : compatible list, contains "qcom,ufs-phy-qmp-20nm" - or "qcom,ufs-phy-qmp-14nm" according to the relevant phy in use. +- compatible : compatible list, contains one of the following - + "qcom,ufs-phy-qmp-20nm" for 20nm ufs phy, + "qcom,ufs-phy-qmp-14nm" for legacy 14nm ufs phy, + "qcom,msm8996-ufs-phy-qmp-14nm" for 14nm ufs phy + present on MSM8996 chipset. - reg : should contain PHY register address space (mandatory), - reg-names : indicates various resources passed to driver (via reg proptery) by name. Required "reg-names" is "phy_mem". diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index f4262ed60582..ad8ea56a9ed3 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -6,9 +6,9 @@ Required properties: - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers used in host mode. - reg: Address and length of the register set for the device - - interrupts: Should contain ehci interrupt + - interrupts: Should contain ohci interrupt - clocks: Should reference the peripheral, host and system clocks - - clock-names: Should contains two strings + - clock-names: Should contain three strings "ohci_clk" for the peripheral clock "hclk" for the host clock "uhpck" for the system clock @@ -35,7 +35,7 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain ehci interrupt - clocks: Should reference the peripheral and the UTMI clocks - - clock-names: Should contains two strings + - clock-names: Should contain two strings "ehci_clk" for the peripheral clock "usb_clk" for the UTMI clock @@ -58,7 +58,7 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - clocks: Should reference the peripheral and the AHB clocks - - clock-names: Should contains two strings + - clock-names: Should contain two strings "pclk" for the peripheral clock "hclk" for the AHB clock @@ -85,7 +85,7 @@ Required properties: - reg: Address and length of the register set for the device - interrupts: Should contain usba interrupt - clocks: Should reference the peripheral and host clocks - - clock-names: Should contains two strings + - clock-names: Should contain two strings "pclk" for the peripheral clock "hclk" for the host clock - ep childnode: To specify the number of endpoints and their properties. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 98371753a08f..16d3b5e7f5d1 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -24,9 +24,11 @@ ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. analogix Analogix Semiconductor, Inc. +andestech Andes Technology Corporation apm Applied Micro Circuits Corporation (APM) aptina Aptina Imaging arasan Arasan Chip Systems +aries Aries Embedded GmbH arm ARM Ltd. armadeus ARMadeus Systems SARL arrow Arrow Electronics @@ -68,6 +70,7 @@ creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. cypress Cypress Semiconductor Corporation +cznic CZ.NIC, z.s.p.o. dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. delta Delta Electronics, Inc. @@ -137,6 +140,7 @@ infineon Infineon Technologies inforce Inforce Computing ingenic Ingenic Semiconductor innolux Innolux Corporation +inside-secure INSIDE Secure intel Intel Corporation intercontrol Inter Control Group invensense InvenSense Inc. @@ -160,6 +164,7 @@ lg LG Corporation linux Linux-specific binding lltc Linear Technology Corporation lsi LSI Corp. (LSI Logic) +macnica Macnica Americas marvell Marvell Technology Group Ltd. maxim Maxim Integrated Products mcube mCube @@ -185,20 +190,24 @@ mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) mundoreader Mundo Reader S.L. murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. +myir MYIR Tech Limited national National Semiconductor nec NEC LCD Technologies, Ltd. neonode Neonode Inc. netgear NETGEAR netlogic Broadcom Corporation (formerly NetLogic Microsystems) netxeon Shenzhen Netxeon Technology CO., LTD +nexbox Nexbox newhaven Newhaven Display International -nvd New Vision Display +ni National Instruments nintendo Nintendo nokia Nokia nuvoton Nuvoton Technology Corporation +nvd New Vision Display nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. +oki Oki Electric Industry Co., Ltd. olimex OLIMEX Ltd. onion Onion Corporation onnn ON Semiconductor Corp. @@ -214,6 +223,7 @@ parade Parade Technologies Inc. pericom Pericom Technology Inc. phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd +pine64 Pine64 pixcir PIXCIR MICROELECTRONICS Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA @@ -235,8 +245,10 @@ realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation richtek Richtek Technology Corporation ricoh Ricoh Co. Ltd. +rikomagic Rikomagic Tech Corp. Ltd rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +samtec Samtec/Softing company sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler @@ -281,6 +293,7 @@ tcg Trusted Computing Group tcl Toby Churchill Ltd. technexion TechNexion technologic Technologic Systems +terasic Terasic Inc. thine THine Electronics, Inc. ti Texas Instruments tlm Trusted Logic Mobility @@ -295,6 +308,7 @@ tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited tyan Tyan Computer Corporation +udoo Udoo uniwest United Western Technologies Corp (UniWest) upisemi uPI Semiconductor Corp. urt United Radiant Technology Corporation |