summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: omap5-uevm: remove always_on, boot_on from smps10_out1Kishon Vijay Abraham I2013-10-201-2/+0
| | | | | | | | | | smps10 should be enabled only in the case of host mode. So stop doing always_on, boot_on from smps10_out1. The driver will enable it in host mode. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap4-panda-es: Do not reset gpio1Nishanth Menon2013-10-201-0/+4
| | | | | | | | | | | | | Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which supplies VDD_MPU. Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because MPU voltage switches over to VSET0 voltage value (boot voltage) which is not sufficient to operate the device at OPP100. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-evmsk: Do not reset gpio0Rajendra Nayak2013-10-201-0/+4
| | | | | | | | | | | Do not reset GPIO0 at boot-up because GPIO0 is used on AM335x EVM-SK to control VTT regulators on DDR3. Without this EVM-SK boards fail to boot-up because of DDR3 corruption. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap: Add reset/idle on init bindings for OMAPRajendra Nayak2013-10-204-1/+9
| | | | | | | | | | | | | | | | | | | On OMAP we have co-processor IPs, memory controllers, GPIOs which control regulators and power switches to PMIC, and SoC internal Bus IPs, some or most of which should either not be reset or idled or both at init. (In some cases there are erratas which prevent an IP from being reset) Have a way to pass this information from DT. Update the am33xx/omap4 and omap5 dtsi files with the new bindings for modules which either should not be idled. reset or both. A later patch would cleanup the same information that exists today as part of the hwmod data files. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3: Adapt USB OTG to generic PHY frameworkRoger Quadros2013-10-202-0/+4
| | | | | | | | | | | | | | The generic PHY framewrok expects different properties than the old USB PHY framework. Supply those properties. Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was merged in greg/usb-next. [1] [1] - https://lkml.org/lkml/2013/9/27/581 Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: OMAP5: Remove clock-frequency field for cpu timersSricharan R2013-10-201-1/+0
| | | | | | | | | | | | The arm arch timers frequency are now programmed in the CNTFREQ per-cpu register by the timer code using the secure API [1]. So remove the redundant entry from the dts. [1] http://marc.info/?l=linux-omap&m=138139106312786&w=2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: dra7-evm: Add mmc2 node for eMMC supportBalaji T K2013-10-111-0/+13
| | | | | | | | | Add mmc2 dt node to dra7-evm board and model eMMC vcc as fixed regulator. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: dra7-evm: Add mmc1 node for micro-sd supportBalaji T K2013-10-111-0/+6
| | | | | | | | | | | Add mmc1 dt node to dra7-evm board. Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21) on i2c1 bus. When dt support for gpio-pcf857x is available, input supply will be modelled as cascaded regulator. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: mark TWL6037 as system-power-controllerNishanth Menon2013-10-111-0/+1
| | | | | | | | This allows the palmas pm_power_off to kick in on power off command and switch off the board. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-igep0020: use standard constant for IRQ flagsJavier Martinez Canillas2013-10-111-1/+1
| | | | | | | | | Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added constants for IRQ edge/level triggered types so use it instead of a magic number to enhance the DT readability. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-igep0020: Add HS USB Host supportJavier Martinez Canillas2013-10-111-0/+49
| | | | | | | | | | Add device nodes for the HS USB Host port 1, USB PHY and its required regulator and also pin mux setup for HS USB1 pins. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-igep: Add USB OTG supportJavier Martinez Canillas2013-10-111-0/+9
| | | | | | | | | | | Commit ad871c10b ("ARM: dts: OMAP: Add usb_otg and glue data to O added USB OTG support for most OMAP boards but some OMAP3 boards such as IGEP boards were not updated. This patch adds an USB OTG device node to these board. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable displayDarren Etheridge2013-10-111-0/+48
| | | | | | | | | | Enable the hdmi output and the LCD Controller on BeagleBone Black. Also configure the correct pinmux for output of video data from the SoC to the HDMI encoder. Signed-off-by: Darren Etheridge <detheridge@ti.com> Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add LCDC info into am335x-evmBenoit Parrot2013-10-112-0/+80
| | | | | | | | | | | | | Add LCDC device node in DT for am33xx Add LCDC and Panel info in DT for am335x-evm Changes: - remove redundant/unnecessary SoC specific setting in the board dts - resolved conflicts on for_3.13/dts Signed-off-by: Benoit Parrot <bparrot@ti.com> Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM437X: Add DES nodeJoel Fernandes2013-10-111-0/+7
| | | | | | | | AM437x SoC has a DES3DES module similar to the one on OMAP4. Add DT node for the same. Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM437X: Add AES nodeJoel Fernandes2013-10-111-0/+7
| | | | | | | | AM437x SoC has AES module similar to the one on OMAP4. Add DT node for the same. Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Fix AES interrupt numberJoel Fernandes2013-10-111-1/+1
| | | | | | | | | AES interrupts were previously not used, but after recent changes to omap-aes driver, its being used. Correct the interrupt number to have working PIO mode. Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add AES data and documentationMark A. Greer2013-10-115-0/+53
| | | | | | | | | | | | | Add the generic AM33XX AES module's device tree data and enable it for the am335x-evm, am335x-evmsk, and am335x-bone platforms. Also add Documentation file describing the data for the AES module. Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Joel Fernandes <joelf@ti.com> [joelf@ti.com: Dropped interrupt-parent property, documentation fixups] Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add SHAM data and documentationMark A. Greer2013-10-115-0/+49
| | | | | | | | | | | | | | Add the generic AM33XX SHAM module's device tree data and enable it for the am335x-evm, am335x-evmsk, and am335x-bone platforms. Also add Documentation file describing the data for the SHAM module. Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Joel Fernandes <joelf@ti.com> [joelf@ti.com: Dropped interrupt-parent property, documentation fixups] Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: OMAP4: Add DES3DES nodeJoel Fernandes2013-10-111-0/+9
| | | | | | | | OMAP4 has an DES3DES module that uses the omap-des crypto driver. Add DT entries for the same. Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: OMAP4: Add AES nodeJoel Fernandes2013-10-111-0/+9
| | | | | | | | OMAP4 has an AES module that uses the omap-aes crypto driver. Add DT entries for the same. Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-evm[sdk]: switch mmc1 to 4-bit modeBalaji T K2013-10-112-0/+2
| | | | | | | Set bus-width to make SD card operate in 4 bit mode. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-bone-common: correct mux mode for cmd lineBalaji T K2013-10-111-1/+1
| | | | | | | | | Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order to detect eMMC on BBB and BBW + eMMC cape. Signed-off-by: Balaji T K <balajitk@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add support for IGEP AQUILA EXPANSION board.Enric Balletbo i Serra2013-10-112-0/+17
| | | | | | | | | | | | | | | | | | | The IGEP AQUILA EXPANSION board is a development platform for the IGEP COM AQUILA AM335x boards. The board adds the following connectivity: o USB OTG o USB HOST o HDMI o Ethernet o Serial Debug (3.3V) o 2x46 pin headers o EEPROM Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add support for IGEP COM AQUILAEnric Balletbo i Serra2013-10-111-0/+265
| | | | | | | | | | | | | | | | | | The IGEP COM AQUILA is industrial processors SODIMM module with following highlights: o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor o Cortex-A8 ARM CPU o 3.3 volts Inputs / Outputs use industrial o 256 MB DDR3 SDRAM / 128 Megabytes FLASH o MicroSD card reader on-board o Ethernet controller on-board o JTAG debug connector available o Designed for industrial range purposes Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-boneblack: move fixed regulator to board levelNishanth Menon2013-10-111-7/+7
| | | | | | | | | | | | | | | | 3.3V fixed regulator does not belong to TPS node - as a result the fixed regulator is never probed and MMC is continually deferred due to lack of regulator. Move the fixed regulator to be at root of platform. Cc: Joel Fernandes <joelf@ti.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Tested-by: Balaji T K <balajitk@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-beagle: Add USB OTG PHY detailsRoger Quadros2013-10-111-0/+7
| | | | | | | | Add information about the USB OTG PHY. Without this the OTG port on beagle will not work. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-beagle-xm: Add USB Host supportRoger Quadros2013-10-111-9/+56
| | | | | | | | | | | | Provide RESET GPIO and Power regulator for the USB PHY, the USB Host port mode and the PHY device for the controller. Also provide pin multiplexer information for USB host pins. We also relocate omap3_pmx_core pin definations so that they are close to omap3_pmx_wkup pin definations. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: Use reset-gpios for hsusb2/3_resetRoger Quadros2013-10-111-24/+2
| | | | | | | | We no longer need to model the RESET line as a regulator since the USB phy-nop driver accepts "reset-gpios" property. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap4-panda: Use reset-gpios for hsusb1_resetRoger Quadros2013-10-111-17/+1
| | | | | | | | We no longer need to model the RESET line as a regulator since the USB phy-nop driver accepts "reset-gpios" property. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-beagle: Use reset-gpios for hsusb2_resetRoger Quadros2013-10-111-12/+1
| | | | | | | | We no longer need to model the RESET line as a regulator since the USB phy-nop driver accepts "reset-gpios" property. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: add ethernet alias's for am33xxDan Murphy2013-10-111-0/+2
| | | | | | | | | | | | Set the alias for ethernet0 and ethernet1 so that uBoot can set the MAC address appropriately. Currently u-boot cannot find the alias and there for does not set the MAC address. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: DRA7: Add TPS659038 PMIC nodesKeerthy2013-10-111-0/+112
| | | | | | | | | | | | | | | | | | Add DT nodes for TPS659038 PMIC on DRA7 boards. It is based on top of: http://comments.gmane.org/gmane.linux.ports.arm.omap/102459. Documentation: - Documentation/devicetree/bindings/mfd/palmas.txt - Documentation/devicetree/bindings/regulator/palmas-pmic.txt Boot Tested on DRA7 d1 Board. Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Nishanth Menon <nm@ti.com> [bcousson@baylibre.com: Fix indentation and changelog] Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-devkit8000: fix a typo in GMPC nodeAaro Koskinen2013-10-111-1/+1
| | | | | | | | "gpmc,sync-clki-ps" is not defined/documented, it should be "gpmc,sync-clk-ps" instead. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: don't redefine OCP bus and device nodesJavier Martinez Canillas2013-10-113-317/+311
| | | | | | | | | | | | | | The On Chip Peripherals (OCP) device node is a simplified representation of the AM33XX SoC interconnect. An OCP dev node is already defined in the am33xx.dtsi Device Tree source file included by am33xx based boards so there is no need to redefine this on each board DT file. Also, the OCP and IP modules directly connected to it are SoC internal details that is better to keep outside of board files. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: use pinmux node defined in included fileJavier Martinez Canillas2013-10-113-365/+365
| | | | | | | | | | | | | am33xx boards DTS include the am33xx.dtsi Device Tree source file that already define a pinmux device node for the AM33XX SoC Pin Multiplex. Redefining this for each board makes the Device Tree files harder to modify and maintain so let's just use what is already defined in the included .dtsi file. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-bone-common: add cpu0 and mmc1 triggersKoen Kooi2013-10-111-0/+2
| | | | | | | | | | | | | | | | | | | This matches the vendor 3.8.x configuration that is shipping with the boards. The LED layout is now: USR0: heartbeat USR1: mmc0 (micro-SD slot) USR2: cpu0 USR3: mmc1 (eMMC) The cpu0 triggers was put in between the mmc triggers to make is easier to see where the disk activity is. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Tested-by: Kevin Hilman <khilman@linaro.org> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-bone-common: switch mmc1 to 4-bit modeKoen Kooi2013-10-111-0/+1
| | | | | | | | | The micro-SD slot hooks up all four data pins so lets' use them. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Tested-by: Kevin Hilman <khilman@linaro.org> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-boneblack: add eMMC DT entryKoen Kooi2013-10-112-0/+35
| | | | | | | | | | | The pinmux is specified in am335x-bone-common.dtsi to be reused by the eMMC cape. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Tested-by: Kevin Hilman <khilman@linaro.org> Reviewed-by: Nishanth Menon <nm@ti.com> [bcousson@baylibre.com: Fix traling spaces and useless comments] Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: am335x-bone: add CD for mmc1Alexander Holler2013-10-112-1/+14
| | | | | | | | | | This enables the use of MMC cards even when no card was inserted at boot. Signed-off-by: Alexander Holler <holler@ahsoftware.de> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Tested-by: Kevin Hilman <khilman@linaro.org> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add MMC support and documentationMatt Porter2013-10-115-1/+88
| | | | | | | | | | | | | | | | Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards. Also added is the DMA binding definitions based on the generic DMA request binding. Additional changes made to DTS: * Interrupt, reg and compatible properties added * ti,needs-special-hs-handling added Signed-off-by: Matt Porter <mporter@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add SPI DMA supportMatt Porter2013-10-111-0/+10
| | | | | | | | Adds DMA resources to the AM33XX SPI nodes. Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM33XX: Add EDMA supportMatt Porter2013-10-111-0/+12
| | | | | | | | | | | | | | Adds AM33XX EDMA support to the am33xx.dtsi as documented in Documentation/devicetree/bindings/dma/ti-edma.txt [Joel Fernandes <joelf@ti.com>] Drop DT entries that are non-hardware-description as discussed in [1] [1] https://patchwork.kernel.org/patch/2226761/ Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: OMAP5: add palmas-usb nodeFelipe Balbi2013-10-082-1/+13
| | | | | | | | | | | | Without this node, there will be no palmas driver to notify dwc3 that a cable has been connected and, without that, dwc3 will never initialize. Signed-off-by: Felipe Balbi <balbi@ti.com> [kishon@ti.com: added dt properties for enabling vbus/id interrupts and fixed vbus-supply value after SMPS10 is modeled as 2 regulators] Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap3-beagle: Make USB host pin naming consistentRoger Quadros2013-10-081-12/+12
| | | | | | | | Use a common naming scheme "mode0name.modename flags" for the USB host pins to be consistent. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: Add devicetree for gta04 board.Marek Belisko2013-10-082-0/+169
| | | | | | | | This adds devicetree for gta04 (Openmoko next generation board) with necessary support for mmc, usb, leds and button. Signed-off-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM4372: add few nodesAfzal Mohammed2013-10-081-0/+343
| | | | | | | | | | | | | | | | | | | | | | | | | Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes. Reason for adding these nodes early - hwmod code required address space of peripherals corresponding to these nodes (as address space details are removed from hwmod database). uart0, timers - 1 & 2 and synctimer were already present, so here the remaining uarts & timers are added. All properties as per the existing binding has been added for uart, timer, rtc, wdt & gpio. Even though that was not the current scope of work, felt adding those would reduce or require no effort later to get these peripherals working. For i2c, spi, cpsw & pwm - only the properties that were sure to be correct has been added (main intention is to make hwmod happy and avoid any later modification to here added properties). While at it add "ti,hwmod" property to already existing nodes. Signed-off-by: Afzal Mohammed <afzal@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: AM4372: cpu(s) node per latest bindingAfzal Mohammed2013-10-081-0/+4
| | | | | | | | Update AM4372 cpu node to the latest cpus/cpu bindings for ARM. Signed-off-by: Afzal Mohammed <afzal@ti.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm boardR Sricharan2013-10-084-1/+767
| | | | | | | | | | | | | Add minimal device tree source needed for DRA7 based SoCs. Also add a board dts file for the dra7-evm (based on dra752) which contains 1.5G of memory with 1G interleaved and 512MB non-interleaved. Also added in the board file are pin configuration details for i2c, mcspi and uart devices on board. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: twl6030: Move common configuration for OMAP4 boards in a separate ↵Ruslan Bilovol2013-10-083-40/+40
| | | | | | | | | | | | | | | dtsi file The OMAP4 SoC family uses specially-designed PMIC (power management IC) companion chip for power management needs: TWL6030/TWL6032. Therefore there is a typical connection of PMIC to OMAP4 so we can move it into separate .dtsi file and do not duplicate over board-specific files. Tested on OMAP4 SDP board and Pandaboard ES2. Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-23 10:26:44 +0100