| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The current setting reflects about 86 Ohms of source-impedance
on the SDIO signals where the WiFi board is hooked up. PCB traces are
routed with 50 Ohms impedance and there are no serial resistors on
those traces.
This commit changes the source-impedance to 52 Ohms to better match our
hardware design.
The impedances given in this commit message refer to 3.3V operation.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:
- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
| |
This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.
This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
| |
Do not change the clock as the power for this phy is switched
with that clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
| |
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since commit d2d0ad2aec4a ("i2c: imx: use open drain for recovery
GPIO") GPIO lib expects this GPIO to be configured as open drain.
Make sure we define this GPIO as open drain in the device tree.
This gets rid of the following warning:
gpio-81 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Note that currently the i.MX pinctrl driver does not support
enabling open drain directly, so this patch has no effect in
practice. Open drain is enabled by the fixed pinmux entry.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
