| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for the R-Car Gen4 CMT types 0/1 which are the same as in
the previous two generations.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220713100603.3391-4-wsa+renesas@sang-engineering.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220713100603.3391-3-wsa+renesas@sang-engineering.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220713100603.3391-2-wsa+renesas@sang-engineering.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Fix the following compilation warnings:
timer-microchip-pit64b.c:68: warning: cannot understand function prototype: 'struct mchp_pit64b_clkevt '
timer-microchip-pit64b.c:82: warning: cannot understand function prototype: 'struct mchp_pit64b_clksrc '
timer-microchip-pit64b.c:283: warning: Function parameter or member 'timer' not described in 'mchp_pit64b_init_mode'
timer-microchip-pit64b.c:283: warning: Function parameter or member 'max_rate' not described in 'mchp_pit64b_init_mode'
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220609094041.1796372-4-claudiu.beznea@microchip.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use mchp_pit64b_suspend() and mchp_pit64b_resume() to disable or
enable timers clocks on init and remove specific
clk_prepare_{disable, enable} calls. This is ok also for clockevent timer
as proper clock enable, disable is done on .set_state_oneshot,
.set_state_periodic, .set_state_shutdown calls.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220609094041.1796372-3-claudiu.beznea@microchip.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Remove suspend and resume ops for clockevent and add set_state_oneshot()
instead. Along with this mchp_pit64b_{suspend, resume}() were called on
proper function to disable/enable clocks. This will allow disabling clocks
for clockevent in case it is not selected as active clockevent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220609094041.1796372-2-claudiu.beznea@microchip.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Add support for R-Car S4.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220705195520.2581-1-wsa+renesas@sang-engineering.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Some MediaTek platforms with a buggy TrustZone ATF firmware will not
initialize the AArch64 System Timer correctly: in these cases, the
System Timer address is correctly programmed, as well as the CNTFRQ_EL0
register (reading 13MHz, as it should be), but the assigned hardware
timers are never started before (or after) booting Linux.
In this condition, any call to function get_cycles() will be returning
zero, as CNTVCT_EL0 will always read zero.
One common critical symptom of that is trying to use the udelay()
function (calling __delay()), which executes the following loop:
start = get_cycles();
while ((get_cycles() - start) < cycles)
cpu_relax();
which, when CNTVCT_EL0 always reads zero, translates to:
while((0 - 0) < 0) ==> while(0 < 0)
... generating an infinite loop, even though zero is never less
than zero, but always equal to it (this has to be researched,
but it's out of the scope of this commit).
To fix this issue on the affected MediaTek platforms, the solution
is to simply start the timers that are designed to be System Timer(s).
These timers, downstream, are called "CPUXGPT" and there is one
timer per CPU core; luckily, it is not necessary to set a start bit
on each CPUX General Purpose Timer, but it's conveniently enough to:
- Set the clock divider (input = 26MHz, divider = 2, output = 13MHz);
- Set the ENABLE bit on a global register (starts all CPUX timers).
The only small hurdle with this setup is that it's all done through
the MCUSYS wrapper, where it is needed, for each read or write, to
select a register address (by writing it to an index register) and
then to perform any R/W on a "CON" register.
For example, writing "0x1" to the CPUXGPT register offset 0x4:
- Write 0x4 to mcusys INDEX register
- Write 0x1 to mcusys CON register
Reading from CPUXGPT register offset 0x4:
- Write 0x4 to mcusys INDEX register
- Read mcusys CON register.
Finally, starting this timer makes platforms affected by this issue
to work correctly.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20220613133819.35318-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Document the "CPUXGPT" CPU General Purpose Timer, used as ARM/ARM64
System Timer on MediaTek platforms and add the MT6795 compatible for it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20220613133819.35318-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The timer IP block present on Tegra234 SoC supports watchdog timer
functionality that can be used to recover from system hangs. The
watchdog timer uses a timer in the background for countdown.
Signed-off-by: Kartik <kkartik@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1656922422-25823-4-git-send-email-kkartik@nvidia.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently this only supports a single watchdog, which uses a timer in
the background for countdown. Eventually the timers could be used for
various time-keeping tasks, but by default the architected timer will
already provide that functionality.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1656922422-25823-3-git-send-email-kkartik@nvidia.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20220715015852.12523-1-rdunlap@infradead.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
