| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Write to RXQCTL register to disable the receive queue when configuring
the RX ring.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Re-word the comment to avoid stating that we return a value for this
void function. Additionally, there is no need to mention older kernels,
since this is the upstream kernel.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If some code path executes fm10k_service_event_schedule(), it is
guaranteed that we only queue the service task once, since we use
__FM10K_SERVICE_SCHED flag. Unfortunately this has a side effect that if
a service request occurs while we are currently running the watchdog, it
is possible that we will fail to notice the request and ignore it until
the next time the request occurs.
This can cause problems with pf/vf mailbox communication and other
service event tasks. To avoid this, introduce a FM10K_SERVICE_REQUEST
bit. When we successfully schedule (and set the _SCHED bit) the service
task, we will clear this bit. However, if we are unable to currently
schedule the service event, we just set the new SERVICE_REQUEST bit.
Finally, after the service event completes, we will re-schedule if the
request bit has been set.
This should ensure that we do not miss any service event schedules,
since we will re-schedule it once the currently running task finishes.
This means that for each request, we will always schedule the service
task to run at least once in full after the request came in.
This will avoid timing issues that can occur with the service event
scheduling. We do pay a cost in re-running many tasks, but all the
service event tasks use either flags to avoid duplicate work, or are
tolerant of being run multiple times.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This ensures that future programmers do not have to remember to re-size
the bitmaps due to adding new values. Although this is unlikely for this
driver, it may happen and it's best to prevent it from ever being an
issue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Replace bitwise operators and #defines with a BITMAP and enumeration
values. This is similar to how we handle the "state" values as well.
This has two distinct advantages over the old method. First, we ensure
correctness of operations which are currently problematic due to race
conditions. Suppose that two kernel threads are running, such as the
watchdog and an ethtool ioctl, and both modify flags. We'll say that the
watchdog is CPU A, and the ethtool ioctl is CPU B.
CPU A sets FLAG_1, which can be seen as
CPU A read FLAGS
CPU A write FLAGS | FLAG_1
CPU B sets FLAG_2, which can be seen as
CPU B read FLAGS
CPU A write FLAGS | FLAG_2
However, "|=" and "&=" operators are not actually atomic. So this could
be ordered like the following:
CPU A read FLAGS -> variable
CPU B read FLAGS -> variable
CPU A write FLAGS (variable | FLAG_1)
CPU B write FLAGS (variable | FLAG_2)
Notice how the 2nd write from CPU B could actually undo the write from
CPU A because it isn't guaranteed that the |= operation is atomic.
In practice the race windows for most flag writes is incredibly narrow
so it is not easy to isolate issues. However, the more flags we have,
the more likely they will cause problems. Additionally, if such
a problem were to arise, it would be incredibly difficult to track down.
Second, there is an additional advantage beyond code correctness. We can
now automatically size the BITMAP if more flags were added, so that we
do not need to remember that flags is u32 and thus if we added too many
flags we would over-run the variable. This is not a likely occurrence
for fm10k driver, but this patch can serve as an example for other
drivers which have many more flags.
This particular change does have a bit of trouble converting some of the
idioms previously used with the #defines for flags. Specifically, when
converting FM10K_FLAG_RSS_FIELD_IPV[46]_UDP flags. This whole operation
was actually quite problematic, because we actually stored flags
separately. This could more easily show the problem of the above
re-ordering issue.
This is really difficult to test whether atomics make a difference in
practical scenarios, but you can ensure that basic functionality remains
the same. This patch has a lot of code coverage, but most of it is
relatively simple.
While we are modifying these files, update their copyright year.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
FM10K_REMOVED expects a hardware address, not a 'struct fm10k_hw'.
Fixes: 5cb8db4a4cbc ("fm10k: Add support for VF")
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
People are using bonding over Infiniband IPoIB connections, and who knows
what else. Infiniband has a hardware address length of 20 octets
(INFINIBAND_ALEN), and the network core defines a MAX_ADDR_LEN of 32.
Various places in the bonding code are currently hard-wired to 6 octets
(ETH_ALEN), such as the 3ad code, which I've left untouched here. Besides,
only alb is currently possible on Infiniband links right now anyway, due
to commit 1533e7731522, so the alb code is where most of the changes are.
One major component of this change is the addition of a bond_hw_addr_copy
function that takes a length argument, instead of using ether_addr_copy
everywhere that hardware addresses need to be copied about. The other
major component of this change is converting the bonding code from using
struct sockaddr for address storage to struct sockaddr_storage, as the
former has an address storage space of only 14, while the latter is 128
minus a few, which is necessary to support bonding over device with up to
MAX_ADDR_LEN octet hardware addresses. Additionally, this probably fixes
up some memory corruption issues with the current code, where it's
possible to write an infiniband hardware address into a sockaddr declared
on the stack.
Lightly tested on a dual mlx4 IPoIB setup, which properly shows a 20-octet
hardware address now:
$ cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: fault-tolerance (active-backup) (fail_over_mac active)
Primary Slave: mlx4_ib0 (primary_reselect always)
Currently Active Slave: mlx4_ib0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 100
Down Delay (ms): 100
Slave Interface: mlx4_ib0
MII Status: up
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr:
80:00:02:08:fe:80:00:00:00:00:00:00:e4:1d:2d:03:00:1d:67:01
Slave queue ID: 0
Slave Interface: mlx4_ib1
MII Status: up
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr:
80:00:02:09:fe:80:00:00:00:00:00:01:e4:1d:2d:03:00:1d:67:02
Slave queue ID: 0
Also tested with a standard 1Gbps NIC bonding setup (with a mix of
e1000 and e1000e cards), running LNST's bonding tests.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the mc_list is longer than 256 addresses, we enter mc_promisc mode.
If we're in mc_promisc mode and the firmware doesn't support cascaded
multicast, normally we also insert our mc_list, to prevent stealing by
another VI. However, if the mc_list was too long, this isn't really
helpful - the MC groups that didn't fit in the list can still get
stolen, and having only some of them stealable will probably cause
more confusing behaviour than having them all stealable. Since
inserting 256 multicast filters takes a long time and can lead to MCDI
state machine timeouts, just skip the mc_list insert in this overflow
condition.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support setting link speed and autonegotiation through
set_link_ksettings() ethtool op. If the port is reconfigured
in incompatible way and reboot is required the netdev will get
unregistered and not come back until user reboots the system.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add NSP backend for upcoming link configuration operations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow NSP to set option code even when error is reported. This provides
a way for NSP to give user more precise information about why command
failed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make NSP port structure a union to simplify accessing the fields
from generic macros.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NSP commands may be slow to respond, we should try to avoid doing
a command-per-item when user requested to change multiple parameters
for instance with an ethtool .set_settings() command.
Introduce a way of internal NSP code to carry state in NSP structure
and add start/finish calls to perform the initialization and kick off
of the configuration request, with potentially many parameters being
modified in between.
nfp_eth_set_mod_enable() will make use of the new code internally,
other "set" functions to follow.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will soon add more NSP commands and structure definitions.
Move all high-level NSP header contents to a common nfp_nsp.h file.
Right now it mostly boils down to renaming nfp_nsp_eth.h and
moving some functions from nfp.h there.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Service process firmware provides us with information about media
and interface (SFP module) plugged in, translate that to Linux's
PORT_* defines and report via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NSP ABI version 0.17 is exposing the autonegotiation settings.
Report whether autoneg is on via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the PF prefer the link speed value provided by the NSP.
Refresh port table if needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will need a way of refreshing port state for link settings
get/set. For get we need to refresh port speed and type.
When settings are changed the reconfiguration may require
reboot before it's effective. Unregister netdevs affected
by reconfiguration from a workqueue.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For caching link settings - remember if we have seen link events
since the last time the eth_port information was refreshed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will want to unregister netdevs after their port got reconfigured.
For that we need to make sure manipulations of port list from the
port reconfiguration flow will not race with driver's .remove()
callback.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After port reconfiguration (port split, media type change)
firmware will continue to report old configuration until
reboot. NSP will inform us that reconfiguration is pending.
To avoid user confusion refuse to spawn netdevs until the
new configuration is applied (reboot).
We need to split the netdev to eth_table port matching from
MAC search and move it earlier in the probe() flow.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read link speed from the BAR. This provides very basic information
and works for both PFs and VFs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add a generic testsuite for testing ethernet network device driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netdev events happen, a rtnetlink_event() handler will send
messages for every event in it's white list. These messages contain
current information about a particular device, but they do not include
the iformation about which event just happened. The consumer of
the message has to try to infer this information. In some cases
(ex: NETDEV_NOTIFY_PEERS), that is not possible.
This patch adds a new extension to RTM_NEWLINK message called IFLA_EVENT
that would have an encoding of the which event triggered this
message. This would allow the the message consumer to easily determine
if it is interested in a particular event or not.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtnetlink_event currently functions as a blacklist where
we block cerntain netdev events from being sent to user space.
As a result, events have been added to the system that userspace
probably doesn't care about.
This patch converts the implementation to the white list so that
newly events would have to be specifically added to the list to
be sent to userspace. This would force new event implementers to
consider whether a given event is usefull to user space or if it's
just a kernel event.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define one new macro TCP_MAX_WSCALE instead of literal number '14',
and use U16_MAX instead of 65535 as the max value of TCP window.
There is another minor change, use rounddown(space, mss) instead of
(space / mss) * mss;
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit d6580a9f1523 ("kexec: sysrq: simplify sysrq-c handler"),
the sysrq handler for the 'c' key has been sysrq_crash_op. Debugging
code in the ibm_emac driver also tries to register a handler for the 'c'
key, but this has no effect because register_sysrq_key() doesn't replace
existing handlers. Since evidently no one has cared enough to fix this
in the last 8 years, and it's very rare for drivers to register sysrq
handlers (for good reason), just remove the dead code.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier patch c4adfc822bf5 ("bonding: make speed, duplex setting
consistent with link state") made an attempt to keep slave state
consistent with speed and duplex settings. Unfortunately link-state
transition is used to change the active link especially when used
in conjunction with mii-mon. The above mentioned patch broke that
logic. Also when speed and duplex settings for a link are updated
during a link-event, the link-status should not be changed to
invoke correct transition logic.
This patch fixes this issue by moving the link-state update outside
of the bond_update_speed_duplex() fn and to the places where this fn
is called and update link-state selectively.
Fixes: c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cb_running is reported in /proc/self/net/netlink and it is reported by
the ss tool, when it gets information from the proc files.
sock_diag is a new interface which is used instead of proc files, so it
looks reasonable that this interface has to report no less information
about sockets than proc files.
We use these flags to dump and restore netlink sockets.
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should be returning -ENOMEM if qed_mcp_cmd_add_elem() fails. The
current code returns success.
Fixes: 4ed1eea82a21 ("qed: Revise MFW command locking")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We accidentally left this dead code behind after commit 5952fde10c35
("net: sched: choke: remove dead filter classify code").
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a cut and paste bug here so we accidentally clear the first
few bytes of "resp" a second time instead clearing "ctx".
Fixes: 50c0add534d2 ("liquidio: refactor interrupt moderation code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In hardware configurations where multiple queues are active,
the rx queue needs to be mapped into a dma channel, even if
a single rx queue is used.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add all the currently available SPEED_<foo> strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code enables up to the maximum MSIX vectors in the PCIE
config space without considering the max completion rings available.
An MSIX vector is only useful when it has an associated completion
ring, so it is better to cap it.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No offload is performed on the XDP_TX ring so we can use the short TX
BDs. This has the effect of doubling the size of the XDP TX ring so
that it now matches the size of the rx ring by default.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is necessary to disable autoneg before enabling PHY loopback,
otherwise link won't come up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mac loopback self test operates in polling mode. To support that,
we need to add functions to open and close the NIC half way. The half
open mode allows the rings to operate without IRQ and NAPI. We
use the XDP transmit function to send the loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the basic infrastructure and only firmware tests initially.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add suspend/resume callbacks using the newer dev_pm_ops method.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And add functions to set and free magic packet filter.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add pci shutdown method to put device in the proper WoL and power state.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add code to driver probe function to check if the device is WoL capable
and if Magic packet WoL filter is currently set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Features added include WoL and selftest.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the Holt HI-311x CAN controller. The HI311x
CAN controller is capable of transmitting and receiving standard data
frames, extended data frames and remote frames. The HI311x interfaces
with the host over SPI.
Datasheet: www.holtic.com/documents/371-hi-3110_v-rev-jpdf.do
Signed-off-by: Akshay Bhat <nodeax@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
