| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
My static checker rule complains about this code. The concern is that
if "sample_space" is negative then the "sample_space >= runtime->channels"
condition will not work as intended because it will be type promoted to a
high unsigned int value.
strm->fifo_sample_size is SSI_FIFO_DEPTH (32). The SSIFSR_TDC_MASK is
0x3f. Without any further context it does seem like a reasonable warning
and it can't hurt to add a check for negatives.
Cc: stable@vger.kernel.org
Fixes: 03e786bd4341 ("ASoC: sh: Add RZ/G2L SSIF-2 driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/e07c3dc5-d885-4b04-a742-71f42243f4fd@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
only snd_soc_card_set_bias_level() and snd_soc_card_set_bias_level_post()
are checking "card" in the function, like below
int snd_soc_card_set_bias_level(...)
{
...
=> if (card && card->xxx)
ret = card->xxxx(...);
...
}
But it should already have been an error if "card" was NULL.
remove "card" NULL check here. Otherwise it will get waring on
smatch without this patch. This is prepare for error check cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87msg2knsg.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |\|
| | | |
| | | |
| | | | |
This helps several of my boards in CI.
|
| | | |\ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Merge series from wangweidong.a@awinic.com:
Add the awinic,aw88083 property to support the aw88083 chip.
The driver is for amplifiers aw88083 of Awinic Technology
Corporation. The AW88083 is an intelligent digital audio
amplifier with low noise.
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The driver is for amplifiers aw88083 of Awinic Technology
Corporation. The AW88083 is an intelligent digital audio
amplifier with low noise.
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://patch.msgid.link/20241231125610.465614-3-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The ALC5682I-VD and ALC5682I-VE use the same I2C
codec driver with different calibration settings.
This patch aims to handle their differences.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://patch.msgid.link/20241225094307.3678837-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Remove hard-coded strings by using the str_enabled_disabled() helper
function.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250107011355.2035-1-thorsten.blum@linux.dev
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove hard-coded strings by using the str_yes_no() helper function.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20241230085717.785718-2-thorsten.blum@linux.dev
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently, patch_sdca_function_type() both patches the function type
for older SDCA revisions, and reports the name of the function. In
general it is cleaner to have a single function only do a single
task, so split these operations into two separate functions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241220173516.907406-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
It is not helpful to error out on some SDCA function types, we
might as well report the correct name and let the driver core
simply not bind a driver to those functions for which the code
lacks support. Also given no functions currently have support,
it seems odd to select some as unsupported.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241220173516.907406-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
SDCA only supports 3-bits for the function address, but the ACPI value
is 64-bits. Update the code that parses this to do a bounds check
and error out on invalid addresses. Currently, an invalid address
would truncate to the bottom 3-bits when used and thus use a likely
incorrect address. With the bounds check, it is also now safe to
shrink the size of the adr member of sdca_function_desc to a u8 and
rearrange the struct members to pack better with the new size of adr.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241220173516.907406-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
All the error messages in the SDCA code manually print the function
in the output, update these to use dev_fmt instead. Whilst making
the changes tweak a couple of the error messages to make them a
little shorter.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241220173516.907406-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Several of the SDCA files don't include all the headers they use
locally. These are included by the point of use through other
headers, so it is not currently causing any issues. However, files
should directly include things they directly use, so add the
missing header includes.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241220173516.907406-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Fix sparse warnings:
fsl_asrc_m2m.c:360:45: sparse: warning: incorrect type in argument 1 (different base types)
fsl_asrc_m2m.c:360:45: sparse: expected restricted snd_pcm_format_t [usertype] pcm_forma
fsl_asrc_m2m.c:360:45: sparse: got unsigned int [usertype] format
fsl_asrc_m2m.c:361:41: sparse: warning: incorrect type in assignment (different base types)
fsl_asrc_m2m.c:361:41: sparse: expected restricted snd_pcm_format_t
fsl_asrc_m2m.c:361:41: sparse: got unsigned int [usertype] format
fsl_asrc_m2m.c:365:45: sparse: warning: incorrect type in argument 1 (different base types)
fsl_asrc_m2m.c:365:45: sparse: expected restricted snd_pcm_format_t [usertype] pcm_forma
fsl_asrc_m2m.c:365:45: sparse: got unsigned int [usertype] pcm_format
fsl_asrc_m2m.c:366:42: sparse: warning: incorrect type in assignment (different base types)
fsl_asrc_m2m.c:366:42: sparse: expected restricted snd_pcm_format_t
fsl_asrc_m2m.c:366:42: sparse: got unsigned int [usertype] pcm_format
fsl_asrc_m2m.c:595:54: sparse: warning: incorrect type in assignment (different base types)
fsl_asrc_m2m.c:595:54: sparse: expected unsigned int [usertype] formats
fsl_asrc_m2m.c:595:54: sparse: got restricted snd_pcm_format_t [assigned] [usertype] k
Fixes: 24a01710f627 ("ASoC: fsl_asrc_m2m: Add memory to memory function")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412180043.PAA4t4sQ-lkp@intel.com/
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/20241218024358.3022635-1-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The variable ret is being assigned a zero value that is never read,
it is being re-assigned a new value from the return value from the
call to snd_soc_dapm_add_routes. The assignment is redundant and can
be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20241217171151.354550-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The header clearly states that it does not want to be included directly,
only via '<linux/bitmap.h>'. Replace the include accordingly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241217070545.2533-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add handling of clock related to secondary MI2S_RX in startup, shutdown
and hw params routines. The handing of MI2S_TX and SEC_MI2S clock is
already there so this requires only placing SECONDARY_MI2S_RX in the
correct switch-case choices.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241205023344.2232529-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |\ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
This series adds TGL and MTL matches for configurations using the
Cirrus Logic CDB35L56-EIGHT-C board.
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This adds a match entry for using all the amps on a CDB35L56-EIGHT-C board
without the CS42L43 codec. Configuration is:
SDW0: 4x CS35L56 (OUT1, OUT2, OUT3, OUT4)
SDW1: 4x CS35L56 (OUT5, OUT6, OUT7, OUT8)
Speaker playback and amp feedback are aggregated.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241216032721.131227-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This adds a match for the CDB35L56-EIGHT-C board with SmartCodec and
SmartAmp speakers aggregated.
The configuration is:
SDW0: CS35L56 x2 (SmartAmp) using OUT1 and OUT2
SDW1: CS35L56 x2 (SmartAmp) using OUT7 and OUT8
SDW3: CS42L43 (SmartJack, SmartMic, SmartAmp)
CS35L56 and CS42L43 Speaker playback is aggregated across all 3 buses.
The device addresses and reset arrangements of the EIGHT-C board are
quirky hence the use of non-contiguous outputs OUT1,2,7,8.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241216032721.131227-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This adds match entries for the eight CS35L56 amps on the Cirrus Logic
CDB35L56-EIGHT-C board. Speaker playback and amp feedback are aggregated
across all amps on both SoundWire buses.
The mapping of SoundWire addresses to AMPn numbers matches the actual
order of amps on the EIGHT-C board. The SoundWire unique ID is in reverse
order for amps 1..4 on these boards, and the amp resets are paired
1+8, 2+7, 3+6, 4+5.
This then makes the entries from cs35l56_sdw_eight_1_4_fb_adr and
cs35l56_sdw_eight_5_8_fb_adr match the way the amp resets are paired on
the EIGHT-C board.
[0] = 1 + 8
[1] = 2 + 7
[3] = 3 + 6
[4] = 4 + 5
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241216032721.131227-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
hda_to_sdw() has been unused since it was added in 2020 as part of the
commit d1ede0641b05 ("ASoC: rt715: add RT715 codec driver")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20241216135110.53426-1-linux@treblig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Original sample-card assumes SND_SOC_CLOCK_IN is used for
snd_soc_dai_set_sysclk(), but someday, Codec uses SND_SOC_CLOCK_IN
and CPU uses SND_SOC_CLOCK_OUT at hw_params(), and dai->clk_direction
is used at simple_init_dai().
There is no uniformity today. Let's use dai->clk_direction for all cases.
Fortunately, almost all DAI doesn't care about "dir"
(= SND_SOC_CLOCK_IN/OUT) in .set_sysclk callback function (which is called
in snd_soc_dai_set_sysclk()), so this patch has no effect in such DAIs.
But this patch might breaks some existing Sound Card. Use
"system-clock-direction-out" property if it needs to use SND_SOC_CLOCK_OUT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87y10lu0gx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
commit 1f5664351410 ("ASoC: lower "no backend DAIs enabled for ... Port"
log severity") ignores -EINVAL error message on common soc_pcm_ret().
It is used from many functions, ignoring -EINVAL is over-kill.
The reason why -EINVAL was ignored was it really should only be used
upon invalid parameters coming from userspace and in that case we don't
want to log an error since we do not want to give userspace a way to do
a denial-of-service attack on the syslog / diskspace.
So don't use soc_pcm_ret() on .prepare callback is better idea.
Link: https://lore.kernel.org/r/87v7vptzap.wl-kuninori.morimoto.gx@renesas.com
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87bjxg8jju.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
commit a22ae72b86a4 ("ASoC: soc-core: disable route checks for legacy
devices") added card->disable_route_checks to disable route checks
for legacy devices at soc_probe_component() and snd_soc_bind_card().
And commit 6974857c2b2c ("ASoC: topology: Do not ignore route checks
when parsing graphs") tidyup soc-topology for same reason.
In snd_soc_bind_card() case, if snd_soc_dapm_add_routes() (A) error,
but has card->disable_route_checks case (B), it will indicate
dev_info() only, and then, next function (C) will be called.
Thus, "ret" will be over written, and it is handled as non-error.
static int snd_soc_bind_card(...)
{
...
(A) ret = snd_soc_dapm_add_routes(...);
if (ret < 0) {
(B) if (card->disable_route_checks) {
dev_info(...);
} else {
...
goto probe_end;
}
}
(C) ret = snd_soc_dapm_add_routes(...);
...
In soc_probe_component() case, if snd_soc_dapm_add_routes() (a)
error, and has card->disable_route_checks case (b), it will indicate
dev_info(). But there is no next function after that, this means ret is
still indicating error, and will not be over written.
So error handline (c) will be handled, and will return error (d)
static int soc_probe_component(...)
{
...
(a) ret = snd_soc_dapm_add_routes(...);
if (ret < 0) {
(b) if (card->disable_route_checks) {
dev_info(...);
} else {
...
goto err_probe;
}
}
/* see for_each_card_components */
list_add(...);
err_probe:
(c) if (ret < 0)
soc_remove_component(...);
(d) return ret;
}
In soc_tplg_dapm_graph_elems_load() case, snd_soc_dapm_add_routes()
is called in for loop (1). if it was error (2), and doesn't have
card->disable_route_checks case flag (3), it will break from loop.
If card has flag, it will indicate dev_info() and handled as non-error.
But ret is still indicating error in this case. If this error happen
in last of loop, if will return error (4).
static int soc_tplg_dapm_graph_elems_load(...)
{
...
(1) for (i = 0; i < count; i++) {
...
(2) ret = snd_soc_dapm_add_routes(...);
if (ret) {
(3) if (!dapm->card->disable_route_checks) {
dev_err(...);
break;
}
dev_info(...);
}
}
(4) return ret;
}
This patch set "ret = 0" for each case.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Cc: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87wmg5tzra.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |\ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Merge series from Shengjiu Wang <shengjiu.wang@nxp.com>:
This function is base on the accelerator implementation
for compress API:
04177158cf98 ("ALSA: compress_offload: introduce accel operation mode")
Audio signal processing also has the requirement for memory to
memory similar as Video.
This asrc memory to memory (memory ->asrc->memory) case is a non
real time use case.
User fills the input buffer to the asrc module, after conversion, then asrc
sends back the output buffer to user. So it is not a traditional ALSA playback
and capture case.
Because we had implemented the "memory -> asrc ->i2s device-> codec"
use case in ALSA. Now the "memory->asrc->memory" needs
to reuse the code in asrc driver, so the patch 1 and patch 2 is for refining
the code to make it can be shared by the "memory->asrc->memory"
driver.
Other change is to add memory to memory support for two kinds of i.MX ASRC
modules.
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Register m2m platform device,that user can
use M2M feature.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://patch.msgid.link/20241212074509.3445859-7-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Register m2m platform device, that user can
use M2M feature.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://patch.msgid.link/20241212074509.3445859-6-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Implement the ASRC memory to memory function using
the compress framework, user can use this function with
compress ioctl interface.
This feature can be shared by ASRC and EASRC drivers
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://patch.msgid.link/20241212074509.3445859-5-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
ASRC can be used on memory to memory case, define several
functions for m2m usage and export them as function pointer.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://patch.msgid.link/20241212074509.3445859-4-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
ASRC can be used on memory to memory case, define several
functions for m2m usage.
m2m_prepare: prepare for the start step
m2m_start: the start step
m2m_unprepare: unprepare for stop step, optional
m2m_stop: stop step
m2m_check_format: check format is supported or not
m2m_calc_out_len: calculate output length according to input length
m2m_get_maxburst: burst size for dma
m2m_pair_suspend: suspend function of pair, optional.
m2m_pair_resume: resume function of pair
get_output_fifo_size: get remaining data size in FIFO
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://patch.msgid.link/20241212074509.3445859-3-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |\ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
A new set of tokens have been added to SOF topology to indicate that the pause
operation is supported or not on the given PCM device.
Pause is an optional feature that depends on pipeline, topology and modules
used by the PCM.
Add a pause_supported flag to snd_sof_pcm_stream and use this flag in Intel
platform code to keep the pause support enabled or to disable it.
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If the stream's pause_supported flag is false then mask out the PAUSE
support, so user space will be prevented to use it.
Introduce a module parameter to ignore the pause_supported flag, named as
force_pause_support to allow testing of the PAUSE feature.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20241213101123.27318-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
New tokens are added to topology:
1202: SOF_TKN_STREAM_PLAYBACK_PAUSE_SUPPORTED
1203: SOF_TKN_STREAM_CAPTURE_PAUSE_SUPPORTED
The new tokens are used to advertise support for PAUSE/RESUME operation on
a PCM device depending on firmware product, use case, pipeline topology.
The snd_sof_pcm_stream.pause_supported is updated to reflect the advertised
value for the PCM device.
If the token does not exist then the pause_supported is set to false.
Note: it is up to the platform code to use this flag to decide to advertise
the PAUSE support for user space or not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20241213101123.27318-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The following definitions have no users: SOF_DAI_STREAM() and SOF_FORMATS,
they can be dropped from the header file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20241213131717.24071-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Use the SOF_IPC4_MOD_EXT_PARAM_SIZE() macro to set the param size in the
extension part of the IPC message for clarity.
No Functional change as the PARMA_SIZE offset is at 0.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20241213132110.27800-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The SSIF-2 IP is available on the Renesas RZ/G3S SoC. The Renesas RZ/G3S
SoC supports a power-saving mode where power to most of the SoC
components is turned off. Add suspend/resume support to the SSIF-2 driver
to support this power-saving mode.
On SNDRV_PCM_TRIGGER_SUSPEND trigger the SSI is stopped (the stream
user pointer is left untouched to avoid breaking user space and the dma
buffer pointer is set to zero), on SNDRV_PCM_TRIGGER_RESUME software reset
is issued for the SSIF-2 IP and the clocks are re-configured.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-18-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The code initially issued software reset on SNDRV_PCM_TRIGGER_START
action only before starting the first stream. This can be easily moved to
hw_params() as the action is similar to setting the clocks. Moreover,
according to the hardware manual (Table 35.7 Bits Initialized by Software
Reset of the SSIFCR.SSIRST Bit) the software reset action acts also on the
clock dividers bits. Due to this issue the software reset in hw_params()
before configuring the clock dividers. This also simplifies the code in
trigger API.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-17-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add runtime PM support to the ssi driver. This assert/de-assert the
reset lines on runtime suspend/resume. Along with it the de-assertion of
the reset line from probe function was removed as it is not necessary
anymore.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-16-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Enable runtime PM autosuspend support. The chosen autosuspend delay is
zero for immediate autosuspend. In case there are users that need a
different autosuspend delay, it can be adjusted through sysfs.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-15-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
the SSI
The ASoC subsystem takes care of runtime resume/suspend the audio
devices when needed. Just enable the runtime PM on the SSI driver and
let the subsystem runtime resume/suspend it. While at it use directly
the devm_pm_runtime_enable().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-14-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Use goto label names that specify their action. In this way we can have
a better understanding of what is the action associated with the label
by just reading the label name.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-13-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Use a temporary variable for the struct device pointers to avoid
dereferencing.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-12-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Use readl_poll_timeout_atomic() instead of hardcoding something similar.
While at it replace dev_info() with dev_warn_ratelimited() as the
rz_ssi_set_idle() can also be called from IRQ context and if the SSI
idle is not properly set this is at least a warning for user.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-11-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The first argument of the rz_ssi_stream_is_play() is not used. Remove it.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-10-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Remove the rz_ssi_get_dai() function and use directly the
snd_soc_rtd_to_cpu() where needed or the struct device pointer embedded
in the struct rz_ssi_priv objects.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-9-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Remove the pdev member of struct rz_ssi_priv as it is not used.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-8-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The SSI_RATES macro covers 8KHz-48KHz audio frequencies. Update macro
comment to reflect it.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20241210170953.2936724-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There is no need to populate the ckdv[] with invalid dividers as that
part will not be indexed anyway. The ssi->audio_mck/bclk_rate should
always be >= 0. While at it, change the ckdv type as u8, as the divider
128 was previously using the s8 sign bit.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Fixes: 03e786bd43410fa9 ("ASoC: sh: Add RZ/G2L SSIF-2 driver")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20241210170953.2936724-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The stop trigger invokes rz_ssi_stop() and rz_ssi_stream_quit().
- The purpose of rz_ssi_stop() is to disable TX/RX, terminate DMA
transactions, and set the controller to idle.
- The purpose of rz_ssi_stream_quit() is to reset the substream-specific
software data by setting strm->running and strm->substream appropriately.
The function rz_ssi_is_stream_running() checks if both strm->substream and
strm->running are valid and returns true if so. Its implementation is as
follows:
static inline bool rz_ssi_is_stream_running(struct rz_ssi_stream *strm)
{
return strm->substream && strm->running;
}
When the controller is configured in full-duplex mode (with both playback
and capture active), the rz_ssi_stop() function does not modify the
controller settings when called for the first substream in the full-duplex
setup. Instead, it simply sets strm->running = 0 and returns if the
companion substream is still running. The following code illustrates this:
static int rz_ssi_stop(struct rz_ssi_priv *ssi, struct rz_ssi_stream *strm)
{
strm->running = 0;
if (rz_ssi_is_stream_running(&ssi->playback) ||
rz_ssi_is_stream_running(&ssi->capture))
return 0;
// ...
}
The controller settings, along with the DMA termination (for the last
stopped substream), are only applied when the last substream in the
full-duplex setup is stopped.
While applying the controller settings only when the last substream stops
is not problematic, terminating the DMA operations for only one substream
causes failures when starting and stopping full-duplex operations multiple
times in a loop.
To address this issue, call dmaengine_terminate_async() for both substreams
involved in the full-duplex setup when the last substream in the setup is
stopped.
Fixes: 4f8cd05a4305 ("ASoC: sh: rz-ssi: Add full duplex support")
Cc: stable@vger.kernel.org
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20241210170953.2936724-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
