| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Reduce the number of do-while loops by 1. The number of loops should be
number of segment + 1, the +1 is in case deq and enq are on the same
segment. But due to the use of a do-while loop, the expression is
evaluated after executing the loop, thus the loop is executed 1 extra
time.
Changing the do-while loop expression from "<=" to "<", reduces the loop
amount by 1. The expression "<=" would also work if it was a while loop
instead of a do-while loop.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Address debug message inaccuracies in xhci_ring_expansion_needed().
Specifically, remove the portion of the debug message that indicates the
number of enqueue TRBs to be added to the dequeue segment. This part of
the message may mislead and the calculated value is incorrect. Given that
this value is not of significant importance and the statement is not
consistently accurate, it has been omitted.
The specific issues with the debug message that this commit resolves:
- The calculation of the number of TRBs is incorrect. The current
calculation erroneously includes the link TRB, which is reserved.
Furthermore, the calculated number of TRBs can exceed the dequeue
segment, resulting in a misleading debug message.
- The current phrasing suggests that "ring expansion by X is needed,
adding X TRBs moves enqueue Y TRBs into the dequeue segment".
The intended message, however, is "IF the ring is NOT expanded by X,
THEN adding X TRBs moves enqueue Y TRBs into the dequeue segment".
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This helper was only called from one function.
Removing it both reduces lines of code and made it more readable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.
Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.
This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Exynos-based Google Tensor gs101 SoC has a DWC3 compatible USB
controller and can reuse the existing Exynos glue. Add the
google,gs101-dwusb3 compatible and associated driver data. Four clocks
are required for USB for this SoC:
* bus clock
* suspend clock
* Link interface AXI clock
* Link interface APB clock
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240423-usb-dwc3-gs101-v1-2-2f331f88203f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Exynos-based Google Tensor gs101 SoC has a DWC3 compatible USB
controller and can reuse the existing Exynos glue. Update the dt schema
to include the google,gs101-dwusb3 compatible for it.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240423-usb-dwc3-gs101-v1-1-2f331f88203f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
interacting with "usb: misc: onboard_usb_hub: Disable the USB hub clock
on failure"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20240424161202.7e45e19e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Recent commit introduced support for reading Multiport PHYs and
while doing so iterated over an integer variable which runs from
[0-254] in the worst case scenario. But S390 compiler treats it as a
warning and complains that the integer write to string can go to 11
characters. Fix this by modifying iterator variable to u8.
Suggested-by: Johan Hovold <johan@kernel.org>
Fixes: 30a46746ca5a ("usb: dwc3: core: Refactor PHY logic to support Multiport Controller")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404241215.Mib19Cu7-lkp@intel.com/
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240426050512.57384-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Power event IRQ is used for wakeup either when the controller is
SuperSpeed capable but is missing an SuperSpeed PHY interrupt, or when
the GIC is not capable of detecting DP/DM High-Speed PHY interrupts.
The Power event IRQ stat register indicates whether the High-Speed
phy entered and exited L2 successfully during suspend and resume.
Indicate the same for all ports of a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-10-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DWC3 Qcom wrapper currently supports only wakeup configuration
for single port controllers. Read speed of each port connected
to the controller and enable wakeup for each of them accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-9-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On multiport supported controllers, each port has its own DP/DM and
SuperSpeed (if super speed capable) interrupts. As per the bindings,
their interrupt names differ from single-port ones by having a "_x"
added as suffix (x being the port number). Identify from the interrupt
names whether the controller is a multiport controller or not.
Refactor dwc3_qcom_setup_irq() call to parse multiportinterrupts along
with non-multiport ones accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-8-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The logic for requesting interrupts is duplicated for each interrupt. In
the upcoming patches that introduces support for multiport, it would be
better to clean up the duplication before reading mulitport related
interrupts.
Refactor interrupt setup call by adding a new helper function for
requesting the wakeup interrupts. To simplify implementation, make
the display name same as the interrupt name expected in Device tree.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-7-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the compatible string for SC8280 Multiport USB controller from
Qualcomm.
There are 4 power event interrupts supported by this controller
(one for each port of multiport controller). Add all the 4 as
non-optional interrupts for SC8280XP-MP
Also each port of multiport has one DP and one DM IRQ. Add all DP/DM
IRQs related to 4 ports of SC8280XP Teritiary controller.
Also added SuperSpeed PHY interrupt for both Superspeed ports.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-6-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the DWC3 driver supports only single port controller
which requires at least one HS PHY and at most one SS PHY.
But the DWC3 USB controller can be connected to multiple ports and
each port can have their own PHYs. Each port of the multiport
controller can either be HS+SS capable or HS only capable
Proper quantification of them is required to modify GUSB2PHYCFG
and GUSB3PIPECTL registers appropriately.
DWC3 multiport controllers are capable to service at most 15 High Speed
PHYs and 4 Supser Speed PHYs. Add support for detecting, obtaining and
configuring PHYs supported by a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-5-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some SoC's like SA8295P where the tertiary controller is host-only
capable, GEVTADDRHI/LO, GEVTSIZ, GEVTCOUNT registers are not accessible.
Trying to access them leads to a crash.
For DRD/Peripheral supported controllers, event buffer setup is done
again in gadget_pullup. Skip setup or cleanup of event buffers if
controller is host-only capable.
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-4-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All DWC3 Multi Port controllers that exist today only support host mode.
Temporarily map XHCI address space for host-only controllers and parse
XHCI Extended Capabilities registers to read number of usb2 ports and
usb3 ports present on multiport controller. Each USB Port is at least HS
capable.
The port info for usb2 and usb3 phy are identified as num_usb2_ports
and num_usb3_ports and these are used as iterators for phy operations
and for modifying GUSB2PHYCFG/ GUSB3PIPECTL registers accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-3-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add bindings to indicate properties required to support multiport
on Synopsys DWC3 controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-2-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert USB UHCI bindings to DT schema. Documenting aspeed compatibles
and missing properties. Adding aspeed/generic-uhci example and fixing
nodename for the original example.
Signed-off-by: Mohammad Shehar Yaar Tausif <sheharyaar48@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240423150550.91055-1-sheharyaar48@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update Qualcomm PMIC Type-C examples to follow the USB-C connector
schema. The USB-C connector should have three ports (USB HS @0,
SSTX/RX @1 and SBU @2 lanes). Reorder ports accordingly and add SBU port
connected to the SBU mux (e.g. FSA4480).
Reported-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240418-typec-fix-example-v3-1-08f649b6f368@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
jejb@linux.ibm.com no longer works.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
On arm64 machines, swsusp_save() faults if it attempts to access
MEMBLOCK_NOMAP memory ranges. This can be reproduced in QEMU using UEFI
when booting with rodata=off debug_pagealloc=off and CONFIG_KFENCE=n:
Unable to handle kernel paging request at virtual address ffffff8000000000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
Data abort info:
ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000eeb0b000
[ffffff8000000000] pgd=180000217fff9803, p4d=180000217fff9803, pud=180000217fff9803, pmd=180000217fff8803, pte=0000000000000000
Internal error: Oops: 0000000096000007 [#1] SMP
Internal error: Oops: 0000000096000007 [#1] SMP
Modules linked in: xt_multiport ipt_REJECT nf_reject_ipv4 xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c iptable_filter bpfilter rfkill at803x snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg dwmac_generic stmmac_platform snd_hda_codec stmmac joydev pcs_xpcs snd_hda_core phylink ppdev lp parport ramoops reed_solomon ip_tables x_tables nls_iso8859_1 vfat multipath linear amdgpu amdxcp drm_exec gpu_sched drm_buddy hid_generic usbhid hid radeon video drm_suballoc_helper drm_ttm_helper ttm i2c_algo_bit drm_display_helper cec drm_kms_helper drm
CPU: 0 PID: 3663 Comm: systemd-sleep Not tainted 6.6.2+ #76
Source Version: 4e22ed63a0a48e7a7cff9b98b7806d8d4add7dc0
Hardware name: Greatwall GW-XXXXXX-XXX/GW-XXXXXX-XXX, BIOS KunLun BIOS V4.0 01/19/2021
pstate: 600003c5 (nZCv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : swsusp_save+0x280/0x538
lr : swsusp_save+0x280/0x538
sp : ffffffa034a3fa40
x29: ffffffa034a3fa40 x28: ffffff8000001000 x27: 0000000000000000
x26: ffffff8001400000 x25: ffffffc08113e248 x24: 0000000000000000
x23: 0000000000080000 x22: ffffffc08113e280 x21: 00000000000c69f2
x20: ffffff8000000000 x19: ffffffc081ae2500 x18: 0000000000000000
x17: 6666662074736420 x16: 3030303030303030 x15: 3038666666666666
x14: 0000000000000b69 x13: ffffff9f89088530 x12: 00000000ffffffea
x11: 00000000ffff7fff x10: 00000000ffff7fff x9 : ffffffc08193f0d0
x8 : 00000000000bffe8 x7 : c0000000ffff7fff x6 : 0000000000000001
x5 : ffffffa0fff09dc8 x4 : 0000000000000000 x3 : 0000000000000027
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 000000000000004e
Call trace:
swsusp_save+0x280/0x538
swsusp_arch_suspend+0x148/0x190
hibernation_snapshot+0x240/0x39c
hibernate+0xc4/0x378
state_store+0xf0/0x10c
kobj_attr_store+0x14/0x24
The reason is swsusp_save() -> copy_data_pages() -> page_is_saveable()
-> kernel_page_present() assuming that a page is always present when
can_set_direct_map() is false (all of rodata_full,
debug_pagealloc_enabled() and arm64_kfence_can_set_direct_map() false),
irrespective of the MEMBLOCK_NOMAP ranges. Such MEMBLOCK_NOMAP regions
should not be saved during hibernation.
This problem was introduced by changes to the pfn_valid() logic in
commit a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify
pfn_valid()").
Similar to other architectures, drop the !can_set_direct_map() check in
kernel_page_present() so that page_is_savable() skips such pages.
Fixes: a7d9f306ba70 ("arm64: drop pfn_valid_within() and simplify pfn_valid()")
Cc: <stable@vger.kernel.org> # 5.14.x
Suggested-by: Mike Rapoport <rppt@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Co-developed-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Signed-off-by: Yaxiong Tian <tianyaxiong@kylinos.cn>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Link: https://lore.kernel.org/r/20240417025248.386622-1-tianyaxiong@kylinos.cn
[catalin.marinas@arm.com: rework commit message]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In iocg_pay_debt(), warn is triggered if 'active_list' is empty, which
is intended to confirm iocg is active when it has debt. However, warn
can be triggered during a blkcg or disk removal, if iocg_waitq_timer_fn()
is run at that time:
WARNING: CPU: 0 PID: 2344971 at block/blk-iocost.c:1402 iocg_pay_debt+0x14c/0x190
Call trace:
iocg_pay_debt+0x14c/0x190
iocg_kick_waitq+0x438/0x4c0
iocg_waitq_timer_fn+0xd8/0x130
__run_hrtimer+0x144/0x45c
__hrtimer_run_queues+0x16c/0x244
hrtimer_interrupt+0x2cc/0x7b0
The warn in this situation is meaningless. Since this iocg is being
removed, the state of the 'active_list' is irrelevant, and 'waitq_timer'
is canceled after removing 'active_list' in ioc_pd_free(), which ensures
iocg is freed after iocg_waitq_timer_fn() returns.
Therefore, add the check if iocg was already offlined to avoid warn
when removing a blkcg or disk.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240419093257.3004211-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The count field in struct trip_stats, representing the number of times
the zone temperature was above the trip point, needs to be incremented
in thermal_debug_tz_trip_up(), for two reasons.
First, if a trip point is crossed on the way up for the first time,
thermal_debug_update_temp() called from update_temperature() does
not see it because it has not been added to trips_crossed[] array
in the thermal zone's struct tz_debugfs object yet. Therefore, when
thermal_debug_tz_trip_up() is called after that, the trip point's
count value is 0, and the attempt to divide by it during the average
temperature computation leads to a divide error which causes the kernel
to crash. Setting the count to 1 before the division by incrementing it
fixes this problem.
Second, if a trip point is crossed on the way up, but it has been
crossed on the way up already before, its count value needs to be
incremented to make a record of the fact that the zone temperature is
above the trip now. Without doing that, if the mitigations applied
after crossing the trip cause the zone temperature to drop below its
threshold, the count will not be updated for this episode at all and
the average temperature in the trip statistics record will be somewhat
higher than it should be.
Fixes: 7ef01f228c9f ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The conversion from MIDI2 to MIDI1 UMP messages had a leftover
artifact (superfluous bit shift), and this resulted in the bogus type
check, leading to empty outputs. Let's fix it.
Fixes: e9e02819a98a ("ALSA: seq: Automatic conversion of UMP events")
Cc: <stable@vger.kernel.org>
Link: https://github.com/alsa-project/alsa-utils/issues/262
Message-ID: <20240419100442.14806-1-tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Haier Boyue G42 with ALC269VC cannot detect the MIC of headset,
the line out and internal speaker until
ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS quirk applied.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Message-ID: <20240419082159.476879-1-aichao@kylinos.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Even though the boot protocol stipulates otherwise, an exception has
been made for the EFI stub, and entering the core kernel with the MMU
enabled is permitted. This allows a substantial amount of cache
maintenance to be elided, wich is significant when fast boot times are
critical (e.g., for booting micro-VMs)
Once the initial ID map has been populated, the MMU is disabled as part
of the logic sequence that puts all system registers into a known state.
Any code that needs to execute within the window where the MMU is off is
cleaned to the PoC explicitly, which includes all of HYP text when
entering at EL2.
However, the current sequence of initializing the EL2 system registers
is not safe: HCR_EL2 is set to its nVHE initial state before SCTLR_EL2
is reprogrammed, and this means that a VHE-to-nVHE switch may occur
while the MMU is enabled. This switch causes some system registers as
well as page table descriptors to be interpreted in a different way,
potentially resulting in spurious exceptions relating to MMU
translation.
So disable the MMU explicitly first when entering in EL2 with the MMU
and caches enabled.
Fixes: 617861703830 ("efi: arm64: enter with MMU and caches enabled")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: <stable@vger.kernel.org> # 6.3.x
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240415075412.2347624-6-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The Falkor erratum that results in the need for an ISB before clearing
the M bit in SCTLR_ELx only applies to execution at exception level x,
and so the workaround is not needed when disabling the EL1 MMU while
running at EL2.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240415075412.2347624-5-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the commit d2689b6a86b9 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.
In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.
Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86b9 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4601b4b130de ("block: reopen the device in blkdev_reread_part")
lost the propagation of I/O errors from the low-level read of the
partition table to the user space caller of the BLKRRPART.
Apparently some user space relies on, so restore the propagation. This
isn't exactly pretty as other block device open calls explicitly do not
are about these errors, so add a new BLK_OPEN_STRICT_SCAN to opt into
the error propagation.
Fixes: 4601b4b130de ("block: reopen the device in blkdev_reread_part")
Reported-by: Saranya Muruganandam <saranyamohan@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240417144743.2277601-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and
VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs
that support these features but not AVX512. GFNI actually doesn't even
depend on AVX.
This prevents GFNI from being unnecessarily disabled if AVX is disabled
to mitigate the GDS vulnerability.
This also prevents all three features from being unnecessarily disabled
if AVX512VL (or its dependency AVX512F) were to be disabled, but it
looks like there isn't any case where this happens anyway.
Fixes: c128dbfa0f87 ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org
|
|
Add the following Telit FN920C04 compositions:
0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a9 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_sleep_ptr() to discard all PM_SLEEP related
stuff if CONFIG_PM_SLEEP isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240412142317.5191-6-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_ptr() to discard all PM related stuff if CONFIG_PM
isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-5-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-4-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_ptr() to discard all PM related stuff if CONFIG_PM
isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-3-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240412142317.5191-2-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The renesas_usbhs_get_info() wrapper was useful for legacy board code.
Since commit 1fa59bda21c7fa36 ("ARM: shmobile: Remove legacy board code
for Armadillo-800 EVA") in v4.3, it is no longer used outside the USBHS
driver, and provides no added value over dev_get_platdata(), while
obfuscating the real operation.
Drop it, and replace it by dev_get_platdata() in its sole user.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/fa296af4452dfe394a58b75fd44c3bb9591936eb.1713282736.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dwc->maximum_speed is determined through the device capability and
designer's constraint through device tree binding. If none of them
applies, don't let the default coreConsultant setting in GUCTL1 to limit
the device operating speed.
Normally the default setting will not contradict the device capability
or device tree binding. This scenario was found through our internal
tests, not an actual bug in the wild.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/65003b0cc37c08a0d22996009f548247ad18c00c.1713308949.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the PMIC-GLINK device has orientation GPIOs declared, then it will
report connection orientation. In this case set the flag to mark
registered ports as orientation-aware.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-5-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a callback to allow glue drivers to update the connector before
registering corresponding power supply and Type-C port. In particular
this is useful if glue drivers want to touch the connector's Type-C
capabilities structure.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-4-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use typec_set_orientation() instead of calling typec_switch_set()
manually. This way the rest of the typec framework and the userspace are
notified about the orientation change.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-3-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To simplify the platform code move Type-C orientation handling into the
connector_status callback. As it is called both during connector
registration and on connector change events, duplicated code from
pmic_glink_ucsi_register() can be dropped.
Also this moves operations that can sleep into a worker thread,
removing the only sleeping operation from pmic_glink_ucsi_notify().
Tested-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogeurs@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-2-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow UCSI glue driver to perform addtional work to update connector
status. For example, it might check the cable orientation. This call is
performed after reading new connector statatus, so the platform driver
can peek at new connection status bits.
The callback is called both when registering the port and when the
connector change event is being handled.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-1-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the transfer polling interval is set to 1ms, which is the
frame rate of full-speed and low-speed USB. The USB 2.0 specification
introduces microframes (125 microseconds) to improve the timing
precision of data transfers.
Reducing the transfer interval to 1 microframe increases data throughput
for high-speed and super-speed USB communication
Signed-off-by: Marcello Sylvester Bauer <marcello.bauer@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/6295dbb84ca76884551df9eb157cce569377a22c.1712843963.git.sylv@sylv.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dummy_hcd transfer scheduler assumes that the internal kernel timer
frequency is set to 1000Hz to give a polling interval of 1ms. Reducing
the timer frequency will result in an anti-proportional reduction in
transfer performance. Switch to a hrtimer to decouple this association.
Signed-off-by: Marcello Sylvester Bauer <marcello.bauer@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/57a1c2180ff74661600e010c234d1dbaba1d0d46.1712843963.git.sylv@sylv.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7cd361e2b377a5373968fa7deee4169229992a1e.1713107386.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Cc: stable@vger.kernel.org
Fixes: b311048c174d ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/00122b7cc5be06abef461776e7cc9f5ebc8bc1cb.1713229786.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
