| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Move iop13xx PCI to fixed i/o mapping and remove io.h.
This changes the PCIe bus address to start at 0x10000. Let's hope this
works. If it does not, the alternative would be to revert the value we
write into OIOTVR to zero and set sys->io_offset to 64K.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
iop13xx confuses I/O port numbers with physical addresses, which breaks
legacy ISA I/O access behind PCI bridges and makes it unnecessarily hard
to unify the inb/outb accessors with other platforms. This removes the
special-casing and just puts all I/O ports into a single 128KB virtually
mapped I/O port range starting at port zero.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move orion5x PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move kirkwood PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
The i/o regions are changed from 1MB to 64KB. It's likely that the 2nd
bus is not setup correctly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move footbridge PCI to fixed i/o mapping. io.h is still needed for the
!MMU case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Convert shark to use the fixed i/o mapping and remove io.h.
This shrinks the mapping from 256MB to 1MB, but nothing is using that much
space AFAICT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
No functional changes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move integrator PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move tegra PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move versatile PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
With consolidation of the PCI i/o mappings, the i/o space is being
set to start at a PCI bus addr of 0x0 and fixed to 64K per bus. In
this case the core ARM PCI setup code can setup the i/o resource.
Currently, the resource is only setup if the platform did not setup
an i/o resource.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds a fixed virtual mapping for PCI i/o addresses. The mapping is
located at the last 2MB of vmalloc region (0xfee00000-0xff000000). 2MB
is used to align with PMD size, but IO_SPACE_LIMIT is 1MB. The space
is reserved after .map_io and can be mapped at any time later with
pci_ioremap_io. Platforms which need early i/o mapping (e.g. for vga
console) can call pci_map_io_early in their .map_io function.
This has changed completely from the 1st implementation which only
supported creating the static mapping at .map_io.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@linaro.org>
|
|
Instead of using the custom iop3xx gpio functions, use the gpiolib
variants. This should be functionally the same since the gpiolib
just calls the iop3xx gpio functions. This is needed in preparation
of removing iop3xx mach/io.h headers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
|
|
Remove a bunch of trailing whitespace. No functional changes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
|
|
|
|
The idr_pre_get() function never returns a value < 0. It returns 0 (no
memory) or 1 (OK).
Reported-by: Silva Paulo <psdasilva@yahoo.com>
[ Rewrote Silva's patch, but attributing it to Silva anyway - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
vsyscall_seccomp introduced a dependency on __secure_computing. On
configurations with CONFIG_SECCOMP disabled, compilation will fail.
Reported-by: feng xiangjun <fengxj325@gmail.com>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes a problem that can occur when a lone package object is
wrapped with an outer package object in order to conform to
the ACPI specification. Can affect these predefined names:
_ALR,_MLS,_PSS,_TRT,_TSS,_PRT,_HPX,_DLM,_CSD,_PSD,_TSD
https://bugzilla.kernel.org/show_bug.cgi?id=44171
This problem was introduced in 3.4-rc1 by commit
6a99b1c94d053b3420eaa4a4bc8b2883dd90a2f9
(ACPICA: Object repair code: Support to add Package wrappers)
Reported-by: Vlastimil Babka <caster@gentoo.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: <stable@vger.kernel.org> # 3.4
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
If a seccomp filter program is installed, older static binaries and
distributions with older libc implementations (glibc 2.13 and earlier)
that rely on vsyscall use will be terminated regardless of the filter
program policy when executing time, gettimeofday, or getcpu. This is
only the case when vsyscall emulation is in use (vsyscall=emulate is the
default).
This patch emulates system call entry inside a vsyscall=emulate by
populating regs->ax and regs->orig_ax with the system call number prior
to calling into seccomp such that all seccomp-dependencies function
normally. Additionally, system call return behavior is emulated in line
with other vsyscall entrypoints for the trace/trap cases.
[ v2: fixed ip and sp on SECCOMP_RET_TRAP/TRACE (thanks to luto@mit.edu) ]
Reported-and-tested-by: Owen Kibel <qmewlo@gmail.com>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This can be trivially triggered from userspace by passing in something unexpected.
kernel BUG at fs/locks.c:1468!
invalid opcode: 0000 [#1] SMP
RIP: 0010:generic_setlease+0xc2/0x100
Call Trace:
__vfs_setlease+0x35/0x40
fcntl_setlease+0x76/0x150
sys_fcntl+0x1c6/0x810
system_call_fastpath+0x1a/0x1f
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: stable@kernel.org # 3.2+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 080399aaaf35 ("block: don't mark buffers beyond end of disk as
mapped") exposed a bug in __getblk_slow that causes mount to hang as it
loops infinitely waiting for a buffer that lies beyond the end of the
disk to become uptodate.
The problem was initially reported by Torsten Hilbrich here:
https://lkml.org/lkml/2012/6/18/54
and also reported independently here:
http://www.sysresccd.org/forums/viewtopic.php?f=13&t=4511
and then Richard W.M. Jones and Marcos Mello noted a few separate
bugzillas also associated with the same issue. This patch has been
confirmed to fix:
https://bugzilla.redhat.com/show_bug.cgi?id=835019
The main problem is here, in __getblk_slow:
for (;;) {
struct buffer_head * bh;
int ret;
bh = __find_get_block(bdev, block, size);
if (bh)
return bh;
ret = grow_buffers(bdev, block, size);
if (ret < 0)
return NULL;
if (ret == 0)
free_more_memory();
}
__find_get_block does not find the block, since it will not be marked as
mapped, and so grow_buffers is called to fill in the buffers for the
associated page. I believe the for (;;) loop is there primarily to
retry in the case of memory pressure keeping grow_buffers from
succeeding. However, we also continue to loop for other cases, like the
block lying beond the end of the disk. So, the fix I came up with is to
only loop when grow_buffers fails due to memory allocation issues
(return value of 0).
The attached patch was tested by myself, Torsten, and Rich, and was
found to resolve the problem in call cases.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Reported-and-Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Josh Boyer <jwboyer@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.0+
[ Jens is on vacation, taking this directly - Linus ]
--
Stable Notes: this patch requires backport to 3.0, 3.2 and 3.3.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Properly define the CAMIF interrupt resources. This device have two
interrupts - corresponding to the "codec" and "preview" data paths.
IRQ_CAM is handled internally by the architecture and demultiplexed
to IRQ_S3C2440_CAM_C and IRQ_S3C2440_CAM_P - these interrupts only
should be handled in the driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Use correct gate control bit for AC97 clock which is
S3C2440_CLKCON_AC97, not S3C2440_CLKCON_CAMERA.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The rework of the snd-usb endpoint logic moved the calls to
snd_usb_set_interface() into the snd_usb_endpoint implemenation. This
changed the order in which these calls are issued to the device, and
thereby caused regressions for some webcams.
Fix this by moving the calls back to pcm.c for now to make it work again
and use snd_usb_endpoint_activate() to really tear down all remaining
URBs in the flight, consequently fixing another regression caused by USB
packets on the wire after altsetting 0 has been selected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Philipp Dreimann <philipp@dreimann.net>
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I couldn't find the vendor ID in any of the online databases, but this
mat has a Pump It Up logo on the top side of the controller compartment,
and a disclaimer stating that Andamiro will not be liable on the bottom.
Signed-off-by: Yuri Khan <yurivkhan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Checking for adc->ts_pend already claimed should be done with the
lock held.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The rate of xusbxti clock is set in individual machine files.
The default value should be defined at the clock definition
and individual machine files should modify it if required.
Division by zero in kernel.
[<c0011849>] (unwind_backtrace+0x1/0x9c) from [<c022c663>] (Ldiv0+0x9/0x12)
[<c022c663>] (Ldiv0+0x9/0x12) from [<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78)
[<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78) from [<c0019e67>] (clk_set_rate+0x2f/0x78)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
We were accidentally losing one bit in the configuration register on
device initialization. It was reported to freeze one specific system
right away. Properly preserve all bits we don't explicitly want to
change in order to prevent that.
Reported-by: Stevie Trujillo <stevie.trujillo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit d640113fe80e45ebd4a5b420b introduced a regression on SMP
systems where the processor core with ACPI id zero is disabled
(typically should be the case because of hyperthreading).
The regression got spread through stable kernels.
On 3.0.X it got introduced via 3.0.18.
Such platforms may be rare, but do exist.
Look out for a disabled processor with acpi_id 0 in dmesg:
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] disabled)
This problem has been observed on a:
HP Proliant BL280c G6 blade
This patch restricts the introduced workaround to platforms
with nr_cpu_ids <= 1.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit ca1d72f033 ('PM / Domains: Make it possible to add devices to
inactive domains') introduced possibility to add devices to inactive
power domains and added pm_genpd_dev_need_restore() function which lets
platform core to notify power domain core that the specified device must
be restored (with its runtime_resume() callback) before first use.
This patch adds the pm_genpd_dev_need_restore() call what brings back
the suspend/resume behaviour for the client devices known from the
previous power domain driver (removed by commit 91cfbd4ee0 - 'ARM:
EXYNOS: Hook up power domains to generic power domain infrastructure').
Client device drivers relay on that suspend/resume behaviour, thus this
patch fixes runtime pm operation for client devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Some bootloaders disable unused power domains to reduce power
consuption. Power domain driver can easily read the actual state from
the hardware registers instead of assuming that their initial state is
always 'on'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The macros just called BUG(), but that results in unused variable
warnings all over the place, like in the IPMI driver. The build
regression emails were annoying me, so here's the fix. I have
not even compile tested this, but it's rather obvious.
[ port type mangled to unsigned long ]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
memblock_free_reserved_regions() calls memblock_free(), but
memblock_free() would double reserved.regions too, so we could free the
old range for reserved.regions.
Also tj said there is another bug which could be related to this.
| I don't think we're saving any noticeable
| amount by doing this "free - give it to page allocator - reserve
| again" dancing. We should just allocate regions aligned to page
| boundaries and free them later when memblock is no longer in use.
in that case, when DEBUG_PAGEALLOC, will get panic:
memblock_free: [0x0000102febc080-0x0000102febf080] memblock_free_reserved_regions+0x37/0x39
BUG: unable to handle kernel paging request at ffff88102febd948
IP: [<ffffffff836a5774>] __next_free_mem_range+0x9b/0x155
PGD 4826063 PUD cf67a067 PMD cf7fa067 PTE 800000102febd160
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU 0
Pid: 0, comm: swapper Not tainted 3.5.0-rc2-next-20120614-sasha #447
RIP: 0010:[<ffffffff836a5774>] [<ffffffff836a5774>] __next_free_mem_range+0x9b/0x155
See the discussion at https://lkml.org/lkml/2012/6/13/469
So try to allocate with PAGE_SIZE alignment and free it later.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After commit f5bf18fa22f8 ("bootmem/sparsemem: remove limit constraint
in alloc_bootmem_section"), usemap allocations may easily be placed
outside the optimal section that holds the node descriptor, even if
there is space available in that section. This results in unnecessary
hotplug dependencies that need to have the node unplugged before the
section holding the usemap.
The reason is that the bootmem allocator doesn't guarantee a linear
search starting from the passed allocation goal but may start out at a
much higher address absent an upper limit.
Fix this by trying the allocation with the limit at the section end,
then retry without if that fails. This keeps the fix from f5bf18fa22f8
of not panicking if the allocation does not fit in the section, but
still makes sure to try to stay within the section at first.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.3.x, 3.4.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 238305bb4d41 ("mm: remove sparsemem allocation details from the
bootmem allocator") introduced a bug in the allocation goal calculation
that put section usemaps not in the same section as the node
descriptors, creating unnecessary hotplug dependencies between them:
node 0 must be removed before remove section 16399
node 1 must be removed before remove section 16399
node 2 must be removed before remove section 16399
node 3 must be removed before remove section 16399
node 4 must be removed before remove section 16399
node 5 must be removed before remove section 16399
node 6 must be removed before remove section 16399
The reason is that it applies PAGE_SECTION_MASK to the physical address
of the node descriptor when finding a suitable place to put the usemap,
when this mask is actually intended to be used with PFNs. Because the
PFN mask is wider, the target address will point beyond the wanted
section holding the node descriptor and the node must be offlined before
the section holding the usemap can go.
Fix this by extending the mask to address width before use.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=43871
Reported-by: <dcb314@hotmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
shmem_add_to_page_cache() has three callsites, but only one of them wants
the radix_tree_preload() (an exceptional entry guarantees that the radix
tree node is present in the other cases), and only that site can achieve
mem_cgroup_uncharge_cache_page() (PageSwapCache makes it a no-op in the
other cases). We did it this way originally to reflect
add_to_page_cache_locked(); but it's confusing now, so move the radix_tree
preloading and mem_cgroup uncharging to that one caller.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When adding the page_private checks before calling shmem_replace_page(), I
did realize that there is a further race, but thought it too unlikely to
need a hurried fix.
But independently I've been chasing why a mem cgroup's memory.stat
sometimes shows negative rss after all tasks have gone: I expected it to
be a stats gathering bug, but actually it's shmem swapping's fault.
It's an old surprise, that when you lock_page(lookup_swap_cache(swap)),
the page may have been removed from swapcache before getting the lock; or
it may have been freed and reused and be back in swapcache; and it can
even be using the same swap location as before (page_private same).
The swapoff case is already secure against this (swap cannot be reused
until the whole area has been swapped off, and a new swapped on); and
shmem_getpage_gfp() is protected by shmem_add_to_page_cache()'s check for
the expected radix_tree entry - but a little too late.
By that time, we might have already decided to shmem_replace_page(): I
don't know of a problem from that, but I'd feel more at ease not to do so
spuriously. And we have already done mem_cgroup_cache_charge(), on
perhaps the wrong mem cgroup: and this charge is not then undone on the
error path, because PageSwapCache ends up preventing that.
It's this last case which causes the occasional negative rss in
memory.stat: the page is charged here as cache, but (sometimes) found to
be anon when eventually it's uncharged - and in between, it's an
undeserved charge on the wrong memcg.
Fix this by adding an earlier check on the radix_tree entry: it's
inelegant to descend the tree twice, but swapping is not the fast path,
and a better solution would need a pair (try+commit) of memcg calls, and a
rework of shmem_replace_page() to keep out of the swapcache.
We can use the added shmem_confirm_swap() function to replace the
find_get_page+page_cache_release we were already doing on the error path.
And add a comment on that -EEXIST: it seems a peculiar errno to be using,
but originates from its use in radix_tree_insert().
[It can be surprising to see positive rss left in a memcg's memory.stat
after all tasks have gone, since it is supposed to count anonymous but not
shmem. Aside from sharing anon pages via fork with a task in some other
memcg, it often happens after swapping: because a swap page can't be freed
while under writeback, nor while locked. So it's not an error, and these
residual pages are easily freed once pressure demands.]
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert 4fb5ef089b28 ("tmpfs: support SEEK_DATA and SEEK_HOLE"). I believe
it's correct, and it's been nice to have from rc1 to rc6; but as the
original commit said:
I don't know who actually uses SEEK_DATA or SEEK_HOLE, and whether it
would be of any use to them on tmpfs. This code adds 92 lines and 752
bytes on x86_64 - is that bloat or worthwhile?
Nobody asked for it, so I conclude that it's bloat: let's revert tmpfs to
the dumb generic support for v3.5. We can always reinstate it later if
useful, and anyone needing it in a hurry can just get it out of git.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Josef Bacik <josef@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Dilger <adilger@dilger.ca>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Cc: Jeff liu <jeff.liu@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Requesting a threaded interrupt without a primary handler and without
IRQF_ONESHOT is dangerous, and after commit 1c6c6952 ("genirq: Reject
bogus threaded irq requests"), these requests are rejected. This causes
->probe() to fail, and the RTC driver not to be availble.
To fix, add IRQF_ONESHOT to the IRQ flags.
Tested on OMAP3730/OveroSTORM and OMAP4430/Panda board using rtcwake to
wake from system suspend multiple times.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fat_encode_fh() can fetch an invalid i_pos value on systems where 64-bit
accesses are not atomic. Make it use the same accessor as the rest of the
FAT code.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the OMAP CPUFreq driver to the list of files in the OMAP Power
Management section.
I've already been maintaining this driver, this just makes it official.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code here has a nested spin_lock_irqsave(). It's not needed since
IRQs are already disabled and it causes a problem because it means that
IRQs won't be enabled again at the end. The second call to
spin_lock_irqsave() will overwrite the value of irq_flags and we can't
restore the proper settings.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a bug in the below scenario for !CONFIG_MMU:
1. create a new file
2. mmap the file and write to it
3. read the file can't get the correct value
Because
sys_read() -> generic_file_aio_read() -> simple_readpage() -> clear_page()
which causes the page to be zeroed.
Add SetPageUptodate() to ramfs_nommu_expand_for_mapping() so that
generic_file_aio_read() do not call simple_readpage().
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes
WARNING: at irq/handle.c:146 handle_irq_event_percpu+0x19c/0x1b8()
irq 25 handler mxc_rtc_interrupt+0x0/0xac enabled interrupts
Modules linked in:
(unwind_backtrace+0x0/0xf0) from (warn_slowpath_common+0x4c/0x64)
(warn_slowpath_common+0x4c/0x64) from (warn_slowpath_fmt+0x30/0x40)
(warn_slowpath_fmt+0x30/0x40) from (handle_irq_event_percpu+0x19c/0x1b8)
(handle_irq_event_percpu+0x19c/0x1b8) from (handle_irq_event+0x28/0x38)
(handle_irq_event+0x28/0x38) from (handle_level_irq+0x80/0xc4)
(handle_level_irq+0x80/0xc4) from (generic_handle_irq+0x24/0x38)
(generic_handle_irq+0x24/0x38) from (handle_IRQ+0x30/0x84)
(handle_IRQ+0x30/0x84) from (avic_handle_irq+0x2c/0x4c)
(avic_handle_irq+0x2c/0x4c) from (__irq_svc+0x40/0x60)
Exception stack(0xc050bf60 to 0xc050bfa8)
bf60: 00000001 00000000 003c4208 c0018e20 c050a000 c050a000 c054a4c8 c050a000
bf80: c05157a8 4117b363 80503bb4 00000000 01000000 c050bfa8 c0018e2c c000e808
bfa0: 60000013 ffffffff
(__irq_svc+0x40/0x60) from (default_idle+0x1c/0x30)
(default_idle+0x1c/0x30) from (cpu_idle+0x68/0xa8)
(cpu_idle+0x68/0xa8) from (start_kernel+0x22c/0x26c)
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We should goto error to release memory resource if hotadd_new_pgdat()
failed.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Yasuaki ISIMATU <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the build error:
include/linux/regset.h: In function 'user_regset_copyout_zero':
include/linux/regset.h:289:3: error: implicit declaration of function '__clear_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__gu_val is const if the passed ptr is const, giving:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:442:2: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h:448:4: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h: In function 'fault_in_multipages_readable':
include/linux/pagemap.h:499:3: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h:508:3: error: assignment of read-only variable '__gu_val'
make[4]: *** [init/main.o] Error 1
As we don't care about the actual value of __gu_val in the unhandled
case (it will cause a link error anyway), just remove the assignment.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the build error:
arch/h8300/kernel/time.c: In function 'h8300_timer_tick':
arch/h8300/kernel/time.c:39:2: error: implicit declaration of function 'get_irq_regs' [-Werror=implicit-function-declaration]
arch/h8300/kernel/time.c:39:42: error: invalid type argument of '->' (have 'int')
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
