Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
    Augusto von Dentz.

 2) Add GSO partial support to igc, from Sasha Neftin.

 3) Several cleanups and improvements to r8169 from Heiner Kallweit.

 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
    device self-test. From Andrew Lunn.

 5) Start moving away from custom driver versions, use the globally
    defined kernel version instead, from Leon Romanovsky.

 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.

 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.

 8) Add sriov and vf support to hinic, from Luo bin.

 9) Support Media Redundancy Protocol (MRP) in the bridging code, from
    Horatiu Vultur.

10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.

11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
    Dubroca. Also add ipv6 support for espintcp.

12) Lots of ReST conversions of the networking documentation, from Mauro
    Carvalho Chehab.

13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
    from Doug Berger.

14) Allow to dump cgroup id and filter by it in inet_diag code, from
    Dmitry Yakunin.

15) Add infrastructure to export netlink attribute policies to
    userspace, from Johannes Berg.

16) Several optimizations to sch_fq scheduler, from Eric Dumazet.

17) Fallback to the default qdisc if qdisc init fails because otherwise
    a packet scheduler init failure will make a device inoperative. From
    Jesper Dangaard Brouer.

18) Several RISCV bpf jit optimizations, from Luke Nelson.

19) Correct the return type of the ->ndo_start_xmit() method in several
    drivers, it's netdev_tx_t but many drivers were using
    'int'. From Yunjian Wang.

20) Add an ethtool interface for PHY master/slave config, from Oleksij
    Rempel.

21) Add BPF iterators, from Yonghang Song.

22) Add cable test infrastructure, including ethool interfaces, from
    Andrew Lunn. Marvell PHY driver is the first to support this
    facility.

23) Remove zero-length arrays all over, from Gustavo A. R. Silva.

24) Calculate and maintain an explicit frame size in XDP, from Jesper
    Dangaard Brouer.

25) Add CAP_BPF, from Alexei Starovoitov.

26) Support terse dumps in the packet scheduler, from Vlad Buslov.

27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.

28) Add devm_register_netdev(), from Bartosz Golaszewski.

29) Minimize qdisc resets, from Cong Wang.

30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
    eliminate set_fs/get_fs calls. From Christoph Hellwig.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
  selftests: net: ip_defrag: ignore EPERM
  net_failover: fixed rollback in net_failover_open()
  Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
  Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
  vmxnet3: allow rx flow hash ops only when rss is enabled
  hinic: add set_channels ethtool_ops support
  selftests/bpf: Add a default $(CXX) value
  tools/bpf: Don't use $(COMPILE.c)
  bpf, selftests: Use bpf_probe_read_kernel
  s390/bpf: Use bcr 0,%0 as tail call nop filler
  s390/bpf: Maintain 8-byte stack alignment
  selftests/bpf: Fix verifier test
  selftests/bpf: Fix sample_cnt shared between two threads
  bpf, selftests: Adapt cls_redirect to call csum_level helper
  bpf: Add csum_level helper for fixing up csum levels
  bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
  sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
  crypto/chtls: IPv6 support for inline TLS
  Crypto/chcr: Fixes a coccinile check error
  Crypto/chcr: Fixes compilations warnings
  ...

1 files changed, 253 insertions, 0 deletions

diff --git a/Documentation/networking/skfp.rst b/Documentation/networking/skfp.rst
new file mode 100644
index 000000000000..58f548105c1d
--- /dev/null
+++ b/Documentation/networking/skfp.rst
@@ -0,0 +1,253 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+.. include:: <isonum.txt>
+
+========================
+SysKonnect driver - SKFP
+========================
+
+|copy| Copyright 1998-2000 SysKonnect,
+
+skfp.txt created 11-May-2000
+
+Readme File for skfp.o v2.06
+
+
+.. This file contains
+
+   (1) OVERVIEW
+   (2) SUPPORTED ADAPTERS
+   (3) GENERAL INFORMATION
+   (4) INSTALLATION
+   (5) INCLUSION OF THE ADAPTER IN SYSTEM START
+   (6) TROUBLESHOOTING
+   (7) FUNCTION OF THE ADAPTER LEDS
+   (8) HISTORY
+
+
+1. Overview
+===========
+
+This README explains how to use the driver 'skfp' for Linux with your
+network adapter.
+
+Chapter 2: Contains a list of all network adapters that are supported by
+this driver.
+
+Chapter 3:
+	   Gives some general information.
+
+Chapter 4: Describes common problems and solutions.
+
+Chapter 5: Shows the changed functionality of the adapter LEDs.
+
+Chapter 6: History of development.
+
+
+2. Supported adapters
+=====================
+
+The network driver 'skfp' supports the following network adapters:
+SysKonnect adapters:
+
+  - SK-5521 (SK-NET FDDI-UP)
+  - SK-5522 (SK-NET FDDI-UP DAS)
+  - SK-5541 (SK-NET FDDI-FP)
+  - SK-5543 (SK-NET FDDI-LP)
+  - SK-5544 (SK-NET FDDI-LP DAS)
+  - SK-5821 (SK-NET FDDI-UP64)
+  - SK-5822 (SK-NET FDDI-UP64 DAS)
+  - SK-5841 (SK-NET FDDI-FP64)
+  - SK-5843 (SK-NET FDDI-LP64)
+  - SK-5844 (SK-NET FDDI-LP64 DAS)
+
+Compaq adapters (not tested):
+
+  - Netelligent 100 FDDI DAS Fibre SC
+  - Netelligent 100 FDDI SAS Fibre SC
+  - Netelligent 100 FDDI DAS UTP
+  - Netelligent 100 FDDI SAS UTP
+  - Netelligent 100 FDDI SAS Fibre MIC
+
+
+3. General Information
+======================
+
+From v2.01 on, the driver is integrated in the linux kernel sources.
+Therefore, the installation is the same as for any other adapter
+supported by the kernel.
+
+Refer to the manual of your distribution about the installation
+of network adapters.
+
+Makes my life much easier :-)
+
+4. Troubleshooting
+==================
+
+If you run into problems during installation, check those items:
+
+Problem:
+	  The FDDI adapter cannot be found by the driver.
+
+Reason:
+	  Look in /proc/pci for the following entry:
+
+	     'FDDI network controller: SysKonnect SK-FDDI-PCI ...'
+
+	  If this entry exists, then the FDDI adapter has been
+	  found by the system and should be able to be used.
+
+	  If this entry does not exist or if the file '/proc/pci'
+	  is not there, then you may have a hardware problem or PCI
+	  support may not be enabled in your kernel.
+
+	  The adapter can be checked using the diagnostic program
+	  which is available from the SysKonnect web site:
+
+	      www.syskonnect.de
+
+	  Some COMPAQ machines have a problem with PCI under
+	  Linux. This is described in the 'PCI howto' document
+	  (included in some distributions or available from the
+	  www, e.g. at 'www.linux.org') and no workaround is available.
+
+Problem:
+	  You want to use your computer as a router between
+	  multiple IP subnetworks (using multiple adapters), but
+	  you cannot reach computers in other subnetworks.
+
+Reason:
+	  Either the router's kernel is not configured for IP
+	  forwarding or there is a problem with the routing table
+	  and gateway configuration in at least one of the
+	  computers.
+
+If your problem is not listed here, please contact our
+technical support for help.
+
+You can send email to: linux@syskonnect.de
+
+When contacting our technical support,
+please ensure that the following information is available:
+
+- System Manufacturer and Model
+- Boards in your system
+- Distribution
+- Kernel version
+
+
+5. Function of the Adapter LEDs
+===============================
+
+	The functionality of the LED's on the FDDI network adapters was
+	changed in SMT version v2.82. With this new SMT version, the yellow
+	LED works as a ring operational indicator. An active yellow LED
+	indicates that the ring is down. The green LED on the adapter now
+	works as a link indicator where an active GREEN LED indicates that
+	the respective port has a physical connection.
+
+	With versions of SMT prior to v2.82 a ring up was indicated if the
+	yellow LED was off while the green LED(s) showed the connection
+	status of the adapter. During a ring down the green LED was off and
+	the yellow LED was on.
+
+	All implementations indicate that a driver is not loaded if
+	all LEDs are off.
+
+
+6. History
+==========
+
+v2.06 (20000511) (In-Kernel version)
+    New features:
+
+	- 64 bit support
+	- new pci dma interface
+	- in kernel 2.3.99
+
+v2.05 (20000217) (In-Kernel version)
+    New features:
+
+	- Changes for 2.3.45 kernel
+
+v2.04 (20000207) (Standalone version)
+    New features:
+
+	- Added rx/tx byte counter
+
+v2.03 (20000111) (Standalone version)
+    Problems fixed:
+
+	- Fixed printk statements from v2.02
+
+v2.02 (991215) (Standalone version)
+    Problems fixed:
+
+	- Removed unnecessary output
+	- Fixed path for "printver.sh" in makefile
+
+v2.01 (991122) (In-Kernel version)
+    New features:
+
+	- Integration in Linux kernel sources
+	- Support for memory mapped I/O.
+
+v2.00 (991112)
+    New features:
+
+	- Full source released under GPL
+
+v1.05 (991023)
+    Problems fixed:
+
+	- Compilation with kernel version 2.2.13 failed
+
+v1.04 (990427)
+    Changes:
+
+	- New SMT module included, changing LED functionality
+
+    Problems fixed:
+
+	- Synchronization on SMP machines was buggy
+
+v1.03 (990325)
+    Problems fixed:
+
+	- Interrupt routing on SMP machines could be incorrect
+
+v1.02 (990310)
+    New features:
+
+	- Support for kernel versions 2.2.x added
+	- Kernel patch instead of private duplicate of kernel functions
+
+v1.01 (980812)
+    Problems fixed:
+
+	Connection hangup with telnet
+	Slow telnet connection
+
+v1.00 beta 01 (980507)
+    New features:
+
+	None.
+
+    Problems fixed:
+
+	None.
+
+    Known limitations:
+
+	- tar archive instead of standard package format (rpm).
+	- FDDI statistic is empty.
+	- not tested with 2.1.xx kernels
+	- integration in kernel not tested
+	- not tested simultaneously with FDDI adapters from other vendors.
+	- only X86 processors supported.
+	- SBA (Synchronous Bandwidth Allocator) parameters can
+	  not be configured.
+	- does not work on some COMPAQ machines. See the PCI howto
+	  document for details about this problem.
+	- data corruption with kernel versions below 2.0.33.