diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/ste,mcde.txt')
-rw-r--r-- | Documentation/devicetree/bindings/display/ste,mcde.txt | 104 |
1 files changed, 0 insertions, 104 deletions
diff --git a/Documentation/devicetree/bindings/display/ste,mcde.txt b/Documentation/devicetree/bindings/display/ste,mcde.txt deleted file mode 100644 index 4c33c692bd5f..000000000000 --- a/Documentation/devicetree/bindings/display/ste,mcde.txt +++ /dev/null @@ -1,104 +0,0 @@ -ST-Ericsson Multi Channel Display Engine MCDE - -The ST-Ericsson MCDE is a display controller with support for compositing -and displaying several channels memory resident graphics data on DSI or -LCD displays or bridges. It is used in the ST-Ericsson U8500 platform. - -Required properties: - -- compatible: must be: - "ste,mcde" -- reg: register base for the main MCDE control registers, should be - 0x1000 in size -- interrupts: the interrupt line for the MCDE -- epod-supply: a phandle to the EPOD regulator -- vana-supply: a phandle to the analog voltage regulator -- clocks: an array of the MCDE clocks in this strict order: - MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI - (HDMI clock), DSI0ESCLK (DSI0 energy save clock), - DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy - save clock) -- clock-names: must be the following array: - "mcde", "lcd", "hdmi" - to match the required clock inputs above. -- #address-cells: should be <1> (for the DSI hosts that will be children) -- #size-cells: should be <1> (for the DSI hosts that will be children) -- ranges: this should always be stated - -Required subnodes: - -The devicetree must specify subnodes for the DSI host adapters. -These must have the following characteristics: - -- compatible: must be: - "ste,mcde-dsi" -- reg: must specify the register range for the DSI host -- vana-supply: phandle to the VANA voltage regulator -- clocks: phandles to the high speed and low power (energy save) clocks - the high speed clock is not present on the third (dsi2) block, so it - should only have the "lp" clock -- clock-names: "hs" for the high speed clock and "lp" for the low power - (energy save) clock -- #address-cells: should be <1> -- #size-cells: should be <0> - -Display panels and bridges will appear as children on the DSI hosts, and -the displays are connected to the DSI hosts using the common binding -for video transmitter interfaces; see -Documentation/devicetree/bindings/media/video-interfaces.txt - -If a DSI host is unused (not connected) it will have no children defined. - -Example: - -mcde@a0350000 { - compatible = "ste,mcde"; - reg = <0xa0350000 0x1000>; - interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; - epod-supply = <&db8500_b2r2_mcde_reg>; - vana-supply = <&ab8500_ldo_ana_reg>; - clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */ - <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */ - <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */ - clock-names = "mcde", "lcd", "hdmi"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - dsi0: dsi@a0351000 { - compatible = "ste,mcde-dsi"; - reg = <0xa0351000 0x1000>; - vana-supply = <&ab8500_ldo_ana_reg>; - clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; - clock-names = "hs", "lp"; - #address-cells = <1>; - #size-cells = <0>; - - panel { - compatible = "samsung,s6d16d0"; - reg = <0>; - vdd1-supply = <&ab8500_ldo_aux1_reg>; - reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; - }; - - }; - dsi1: dsi@a0352000 { - compatible = "ste,mcde-dsi"; - reg = <0xa0352000 0x1000>; - vana-supply = <&ab8500_ldo_ana_reg>; - clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; - clock-names = "hs", "lp"; - #address-cells = <1>; - #size-cells = <0>; - }; - dsi2: dsi@a0353000 { - compatible = "ste,mcde-dsi"; - reg = <0xa0353000 0x1000>; - vana-supply = <&ab8500_ldo_ana_reg>; - /* This DSI port only has the Low Power / Energy Save clock */ - clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; - clock-names = "lp"; - #address-cells = <1>; - #size-cells = <0>; - }; -}; |